5008NBA (Type 3) Makita Saw - Overview

This power cord is for power tools. Unplug the power tool before installing this part. Wear work gloves to protect your hands.

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

This part is available individually. The spring washer fits between the wing nut and the flat washer. This washer is small and will need to be replaced if it gets lost or if it breaks. It is made out of metal and no tools should be necessary when replacing this item. This is an OEM Makita part directly sourced from the manufacturer for use with saws, cutters, planers, drills, and trimmers.

This is a genuine Makita replacement part that includes two carbon brushes with wire leads attached. Carbon brushes are essential components in power tools and are among the most commonly replaced parts due to regular wear from friction. Over time, worn brushes can cause a motor to run poorly, operate intermittently, or lose electric brak...Read moreing power. Replacing them can often restore your tool’s performance. A worn brush may appear cracked, pitted, burned, or worn down near the wire lead. It’s always best to replace both brushes at the same time, even if only one shows signs of wear. When installing new brushes, be sure to inspect the armature for any damage such as burns or cracks, which could indicate more serious motor issues.

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls re...Read moreduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

Genuine Makita replacement part, this item is sold individually. The purpose of the Brush Holder Cap is to retain the brush in the brush holder. This Brush Cap is used on all the Makita models listed below. It is removed by using a slotted screwdriver Do not press too hard when removing the cap they do have a tendency to break.

Genuine Makita replacement part, this item is sold individually. The purpose of this lever is to raise and lower the Lower Guard safely on the Makita Saws shown below. To secure the Lever to the Guard, use part number 266026-4 Screw.

This is an authentic Makita replacement part that has been sourced from the original manufacturer to be used with circular saws, table saws, masonry saws, planers, demolition hammers, and angle cutters. The washer has multiple applications based on the model of the power tool. It is recommended to review your model's diagram to verify this washer's compatibility. The washer is sold individually.

This is an authentic OEM part which is designed for use with DeWALT planers. It is a special component which helps to secure the guard. This is an identical replacement for a damaged or a faulty hardware that was installed on a new unit. Check the appropriate diagrams for your model for the exact location and the correct installation of t...Read morehis retaining ring. You will need a wrench set and snap-ring pliers to remove the old part and secure the new one. One durable metal retaining ring is included.

Set of 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an i...Read morentermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. • Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. • Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. • A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. • When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

This cord guard / strain reliever is a genuine Makita replacement part. It covers the final portion of cord before entering the tool, providing extra rigidness and preventing cord damage. Over time these cord guards break down and require replacement. The guard is constructed of heavy duty rubber compound for toughness. This cord guar...Read mored is compatible with the tools listed below. It is not guaranteed to fit any other power tool models.

This is a genuine Makita replacement tapping screw. It is sourced directly from original equipment manufacturer for use with a variety of power equipment. This screw is a piece of standard hardware that has multiple uses depending on your tool. Please check appropriate diagrams to ensure correct location and application for this item. It ...Read moreis a metal pan head screw that requires a screwdriver to install/remove it. Includes one (1) screw per order.