5007NLK Makita Saw - Overview

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

This is a genuine Makita replacement part that includes two carbon brushes with wire leads attached. Carbon brushes are essential components in power tools and are among the most commonly replaced parts due to regular wear from friction. Over time, worn brushes can cause a motor to run poorly, operate intermittently, or lose electric brak...Read moreing power. Replacing them can often restore your tool’s performance. A worn brush may appear cracked, pitted, burned, or worn down near the wire lead. It’s always best to replace both brushes at the same time, even if only one shows signs of wear. When installing new brushes, be sure to inspect the armature for any damage such as burns or cracks, which could indicate more serious motor issues.

This cord is a genuine Makita replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Over time, power tool cords will wear out or become frayed. We recommend replacing a cord as soon as signs of wear are visible. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 8 Feet Long

Genuine Makita replacement part, this item is sold individually. The purpose of the Brush Holder Cap is to retain the brush in the brush holder. This Brush Cap is used on all the Makita models listed below. It is removed by using a slotted screwdriver Do not press too hard when removing the cap they do have a tendency to break.

Authentic replacement part designed for use with circular saws. It helps to secure the saw blade. This genuine Makita hex head bolt is a reverse threaded bolt which is sold individually. When installing or removing it you would need to use a wrench.

This authentic OEM part is compatible with various handheld power tools made by Makita including jig saws, routers, and sanders. A bearing\\\'s main purpose is to decrease friction between moving parts. They also stabilize parts to keep proper direction and angle. Bearings are high wear items that may need regular replacement. Sold individually. Included in part number 517266-0 Armature Assembly 115V

Genuine Makita replacement part, this item is sold individually. The purpose of the 231806-7 Tension Spring is to raise and lower the telescoping lower guard. When you make a cut the Lower Guard will raise up inside of the upper guard, as you get to the end of your cut the Spring will cause the lower guard to return to it original positio...Read moren. The spring is attached to the Lower Guard and also to the upper Guard housing.

This is an authentic OEM part which is designed for use with DeWALT planers. It is a special component which helps to secure the guard. This is an identical replacement for a damaged or a faulty hardware that was installed on a new unit. Check the appropriate diagrams for your model for the exact location and the correct installation of t...Read morehis retaining ring. You will need a wrench set and snap-ring pliers to remove the old part and secure the new one. One durable metal retaining ring is included.

This is a genuine Makita replacement tapping screw. It is sourced directly from original equipment manufacturer for use with a variety of power tools. This hardware has multiple uses depending on your tool. Please make sure to check appropriate diagrams for correct location and application of this item. This pan-head tapping screw is sold individually. You will need a screwdriver to install or remove it.

This replacement inner flange is specially designed for Makita circular and miter saws. It is a genuine item sourced directly from original equipment manufacturer. The purpose of this inner flange is to provide support for the blade. Please note, this metal item is sold individually.

This part has been OEM sourced to ensure quality. The metal flange is intended to be used with circular saws from Makita. This item aligns with the flat sides of the spindle and is used to secure the blade. The flange disperses the pressure but on the blade by the blade bolt across a wider surface area to fasten the blade to the spindle. ...Read moreThis item may require a hex socket wrench to install and is sold as an individual item.

This genuine manufacturer-sourced part is specially designed for use with Makita power tools. It is an identical replacement for a missing or a faulty nut that was installed on a new unit. This is a standard hardware which may have multiple applications. Please make sure to check the appropriate diagrams of your model for the exact locati...Read moreon and application of this component. Keep in mind this high-quality hex lock nut is made of durable metal and is sold individually. Note, you will need a wrench to secure or remove it.