5007NF (Type 1) Makita Saw - Overview

This tapping screw is an authentic hardware that is supplied by original tool manufacturer for use with a variety of Makita power tools. It has multiple uses depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this screw. Note this durable metal screw is sold individually.

This is a genuine Makita replacement part that includes two carbon brushes with wire leads attached. Carbon brushes are essential components in power tools and are among the most commonly replaced parts due to regular wear from friction. Over time, worn brushes can cause a motor to run poorly, operate intermittently, or lose electric brak...Read moreing power. Replacing them can often restore your tool’s performance. A worn brush may appear cracked, pitted, burned, or worn down near the wire lead. It’s always best to replace both brushes at the same time, even if only one shows signs of wear. When installing new brushes, be sure to inspect the armature for any damage such as burns or cracks, which could indicate more serious motor issues.

This cord is a genuine Makita replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Over time, power tool cords will wear out or become frayed. We recommend replacing a cord as soon as signs of wear are visible. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 8 Feet Long

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls re...Read moreduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

Genuine Makita replacement part, this item is sold individually. The purpose of the Brush Holder Cap is to retain the brush in the brush holder. This Brush Cap is used on all the Makita models listed below. It is removed by using a slotted screwdriver Do not press too hard when removing the cap they do have a tendency to break.

It is an OEM sourced part which is made for use with Makita circular saws. The base holds all the components of the saw while also providing support during a cut. If the base is warped or damaged, this will provide an identical replacement for the original part that was installed on a new unit. This high-quality base is made of durable me...Read moretal and is sold individually. Note, the hardware to secure it is sold separately. A screwdriver will be needed to remove and attach the base.

This item is a genuine Makita part that has been sourced from the original manufacturer to be used with trimmers, circular saws, sanders, routers, nailers, reciprocating saws, laminate trimmers, and planers. The flat washer is used with different types of power tools and the application of the washer can vary based on the model of the equipment. This item is available as an individual replacement part.

This is an authentic OEM part which is designed for use with DeWALT planers. It is a special component which helps to secure the guard. This is an identical replacement for a damaged or a faulty hardware that was installed on a new unit. Check the appropriate diagrams for your model for the exact location and the correct installation of t...Read morehis retaining ring. You will need a wrench set and snap-ring pliers to remove the old part and secure the new one. One durable metal retaining ring is included.

This replacement hardware is a genuine OEM sourced part, it is not an aftermarket imitation. It is a commonly used with Makita power tools. This standard hardware has multiple applications depending on the tool. Please refer to appropriate diagrams for correct location and use of this screw. It is a pan head screw which is sold individual...Read morely. You will need a Phillips head screwdriver to install or remove this hardware.

This replacement part is an authentic OEM bolt designed for Makita circular saws. The purpose of this bolt is to secure saw blade to the spindle which driver it. This hex socket head bolt is sold individually. Please note, you would need a hex key/allen wrench to install/remove this bolt.

This genuine OEM replacement part used on some Makita Circular Saws. This is a Plastic Switch and it is sold individually. Switches are commonly replaced parts in power tools. A switch handles on/off and variable speed functions. They also have a role in electric breaking; they can momentarily reverse electrical polarity. Because switche...Read mores use mechanical internals, they will degrade and wear out over time, eventually requiring replacement.