5007NBK Makita Circular Saw - Overview

This trigger switch is for circular saws. Trigger switch starts and stops the circular saw. Unplug the circular saw before installing this part. Wear work gloves to protect your hands.

This power cord is for power tools. Unplug the power tool before installing this part. Wear work gloves to protect your hands.

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

This part is available individually. The spring washer fits between the wing nut and the flat washer. This washer is small and will need to be replaced if it gets lost or if it breaks. It is made out of metal and no tools should be necessary when replacing this item. This is an OEM Makita part directly sourced from the manufacturer for use with saws, cutters, planers, drills, and trimmers.

This is a genuine Makita replacement part that includes two carbon brushes with wire leads attached. Carbon brushes are essential components in power tools and are among the most commonly replaced parts due to regular wear from friction. Over time, worn brushes can cause a motor to run poorly, operate intermittently, or lose electric brak...Read moreing power. Replacing them can often restore your tool’s performance. A worn brush may appear cracked, pitted, burned, or worn down near the wire lead. It’s always best to replace both brushes at the same time, even if only one shows signs of wear. When installing new brushes, be sure to inspect the armature for any damage such as burns or cracks, which could indicate more serious motor issues.

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls re...Read moreduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

Genuine Makita replacement part, this item is sold individually. The purpose of the Brush Holder Cap is to retain the brush in the brush holder. This Brush Cap is used on all the Makita models listed below. It is removed by using a slotted screwdriver Do not press too hard when removing the cap they do have a tendency to break.

This shoe base is supplied directly from the original equipment manufacturer. Compatible with many circular saws, this metal component is sold individually. For making the replacement, you will need a screwdriver and pliers. It is also recommended to refer to the manual for further repair instructions.

Genuine Makita replacement part, this item is sold individually. The purpose of the 231806-7 Tension Spring is to raise and lower the telescoping lower guard. When you make a cut the Lower Guard will raise up inside of the upper guard, as you get to the end of your cut the Spring will cause the lower guard to return to it original positio...Read moren. The spring is attached to the Lower Guard and also to the upper Guard housing.

This Makita circular saw lower pivoting blade guard is a direct replacement for many of Makita\\\'s most popular side-motor saws. This is an OEM part--not after market or generic--and it is manufactured by Makita. This is the pivoting lower guard only and does not include the pivot lever or mounting hardware. Please select your saw from the table below for a complete parts listing.

Genuine Makita replacement part, this item is sold individually. The purpose of this lever is to raise and lower the Lower Guard safely on the Makita Saws shown below. To secure the Lever to the Guard, use part number 266026-4 Screw.

This is an authentic Makita replacement part that has been sourced from the original manufacturer to be used with circular saws, table saws, masonry saws, planers, demolition hammers, and angle cutters. The washer has multiple applications based on the model of the power tool. It is recommended to review your model's diagram to verify this washer's compatibility. The washer is sold individually.