EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

4KSRS22QDW00 KitchenAid Refrigerator - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replacement Ice Maker – Part Number: 4317943
$120.55
In Stock
Replacement Ice Maker
★★★★★
★★★★★
(249)
Part #4317943
This ice maker (Complete Icemaker Assembly, Whirlpool Icemaker Kit, Ice Maker Assembly, Refrigerator Ice Maker, Icemaker) receives water from the water inlet valve, freezes it, and dispenses it into the ice bucket until the bucket is full. Ice makers will need to be replaced every 3-10 years depending on the frequency of usage, and water quality. You can perform a voltage test with a multimeter or perform an inlet valve test. If you’re unable to make ice, or notice leaks then it may be a sign your ice maker is damaged and could be in need of a replacement. This model measures approximately 11x5 inches, is constructed of plastic and metal, and comes in black/silver. This ice maker is a complete assembly; the whole assembly attaches to the wall of your freezer. ***NOTE: Ice maker does NOT come with the bail or shut off arm. You must order them separately if required. It does come complete with flat and round plug wiring harness, the mounting hardware, and the instructions. The harness can be reused. The ice maker will not fit refrigerators that have the ice auger mounted on the door.
Refrigerator Door Cam – Part Number: WPW10329686
$9.62
In Stock
Refrigerator Door Cam
★★★★★
★★★★★
(73)
Part #WPW10329686
The Door Cam is a black plastic part which helps the door pivot shut while keeping the door and hinge in proper alignment. Lubricating this part upon installation may help it move easier. It attaches onto the door hinge and should be replaced if broken or if there is noticeable damage. Refer to your model number and user manual to ensure this is the correct part for you. To do this repair you will need a 5/6 nut driver, a 5/16 socket, and a ratchet. For safety purposes, do not forget to turn off your appliance before making this repair. Note that this piece is black, and as per the manufacturer requires a new screw to mount the door cam which is sold individually. Please also note that this is the closing cam for the lower door, and the upper door cam is sold as a separate kit.
Refrigerator Bimetal Defrost Thermostat – Part Number: WPW10225581
$34.74
In Stock
Refrigerator Bimetal Defrost Thermostat
★★★★★
★★★★★
(30)
Part #WPW10225581
If you have ice building up in your freezer, or if your freezer is getting too warm during the defrost cycle you may need to replace the bi-metal defrost thermostat. The function of the defrost bi-metal thermostat is to clip onto the evaporator and protect your evaporator from overheating during the defrost cycle. If your refrigerator does not defrost properly you can test both the thermostat and the heater to figure out which part is at fault. For this repair, you will need a Phillips screwdriver, a 1/4 inch nut driver, a flat blade screwdriver, a pair of wire strippers, a roll of electrical tape, and a few butt splice connectors.
Refrigerator Ice Bin Auger Drum – Part Number: 4388736
$53.20
In Stock
Refrigerator Ice Bin Auger Drum
★★★★★
★★★★★
(30)
Part #4388736
This white ice bin auger drum comes with a washer.
Door Closing Cam Kit – Part Number: 4318165
$22.52
In Stock
Door Closing Cam Kit
★★★★★
★★★★★
(30)
Part #4318165
This door closing cam kit is intended for use with the bottom of refrigerator and freezer door hinges. The cam helps with the closing of the doors and to keep them slightly in position when opened.
Shelf Support Stud - White – Part Number: 4388538
$25.75
In Stock
Shelf Support Stud - White
★★★★★
★★★★★
(10)
Part #4388538
This kit contains two options - One that is a push and turn and the other that is a screw in.
Ice Maker Water Fill Tube Kit – Part Number: WP2196157
$18.65
In Stock
Ice Maker Water Fill Tube Kit
★★★★★
★★★★★
(27)
Part #WP2196157
The icemaker water fill tube provides water to the icemaker so it can produce ice and dispense water. If you notice that your ice maker is not making or dispensing ice, or is leaking, you may need to replace the water fill tube. This water fill tube kit comes with a fill tube and a compression nut. This part is made of white plastic and is approximately 10 inches in length. The ice maker water fill tube is in the rear of the fridge. To complete this repair, you will need a 1/4 inch nut driver and a utility knife. Before beginning this repair, you may want to disconnect the water and power supply to the refrigerator.
Screw – Part Number: W11233072
$21.45
In Stock
Screw
★★★★★
★★★★★
(6)
Part #W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.
Meat Drawer Cover and Shelf Frame – Part Number: WP2161491
$99.28
In Stock
Meat Drawer Cover and Shelf Frame
★★★★★
★★★★★
(23)
Part #WP2161491
This part contains molded glide rails for the crisper pan. It does not come with the glass shelving.
Refrigerator Micro Switch – Part Number: WP2162361
$20.37
In Stock
Refrigerator Micro Switch
★★★★★
★★★★★
(18)
Part #WP2162361
This switch is located inside the dispenser.
Shelf Stud – Part Number: W11581579
No Longer Available
Shelf Stud
★★★★★
★★★★★
(10)
Part #W11581579
This is a 6 piece kit.
Refrigerator End Cap Trim Piece – Part Number: WP2156006
$10.70
In Stock

Common Symptoms of the 4KSRS22QDW00

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice Maker quit working, I could manually cycle unit but then the water would overflow when unit was re-filling.
596 of 639 people found this instruction helpful.
  • Max from Green Castle, IN
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I backed out the 2 top screws about a quarter inch and then removed bottem screw with a quater inch nut driver. I then lifted Ice Maker clear of the two top screws and lowered it enough to unclip the power connection with a small screwdriver. The new Ice Maker was wired correctley for my refrigeator so all I had to do wea reconnect the power connection and mount new Ice Maker on the two top screws and install the bottem screw. It took e while for the new Ice Maker to start it's cycle but after it did, it worked GREAT. Part Select service was OUTSTANDING, ordered part one day and received the next. THANKS!!!!
Was this helpful?
Thank you for voting!
No Ice in the Ice Maker
201 of 237 people found this instruction helpful.
  • Chris from Duluth, GA
  • Really Easy
  • Less than 15 mins
  • Socket set
I am NOT a handyman, and my family laughed at me when I said I was going to fix the ice maker all by myself. I ordered a replacement ice maker. When it arrived, I opened the box and read the instructions. It seemed easy. I removed the old ice maker, with a socket set. I then took off the shut off lever from the old one and placed it on the new one, since the new one didn't come with it. I then put the new one in place. All the parts fit perfectly. The ice machine was making ice within an hour. My family was amazed... and I got the last laugh!
Was this helpful?
Thank you for voting!
Plastic bits dispensed from Ice Dispenser in Door
205 of 254 people found this instruction helpful.
  • john from seaford, VA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
Removed Ice bin from Fridge

Removed all bolts on bin with nut driver...about six

Removed housing...be careful with spring on crusher/cube control rod

Removed C clamp on end of auger with small slotted screw driver and needle nose pliers.

Removed plastic nut on end of auger shaft

Remov ed Ice crusher jaws and laid them out in the correct order

Removed Ice propeller and installed new part

Put back together in opposite order

Easy
Was this helpful?
Thank you for voting!