Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 4KP26M1XMR5

4KP26M1XMR5 KitchenAid Mixer - Overview

Get Parts and Repair Help for 4KP26M1XMR5

If you know the mixer repair part you need, you can browse the list of all parts on the 4KP26M1XMR5, or you can search by name or part description. You can also find your part by where it is located on the 4KP26M1XMR5 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your mixer. We’ve also included any installation videos we have for 4KP26M1XMR5 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Manuals & Care Guides for 4KP26M1XMR5

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?


Used in Stand Mixers.


Retaining Ring

This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter. The retaining ring is a genuine OEM part sourced directly from the manufacturer. The ring may vary in appearance due to manufacturer substitution, but the function is the same. You may need to replace this part if the dryer is noisy during tumbling, will not tumble, or takes too long to dry. Be sure to check drum support roller kit and shaft before ordering parts.



Used in Stand Mixers.


Worm Gear

Sold individually.


Thumb Screw - Black

This part is used with the stand mixers attachments, as well as to hold the end cap to the front of the mixer.


Retaining Ring

Used on Stand Mixers.


Front Bearing

Used in Mixers.


Thrust Bearing Kit

This bearing comes equipped with two washers and is used on stand mixers.


Retaining Pin

This part works in conjunction with the worm and bevel gear.


Grease - Approx. 1 pound

This grease is used for the Kitchenaid stand mixers for the planetary gears.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

wouldnt turn beaters

  • Customer: Barry from Rowland Heights, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 69 of 74 people found this instruction helpful
removed metal strap around motor housing then remove the 4 screws holding top motor cover on, then removed the 4 screws that hold gear cover in place, remove long gear that is driven by the motor gear, then with ring pliers remove ring off long drive shaft and lift off worm gears. once all gears are removed --removed all the old grease ( do this to get all t... read more

Mixer Made Very Bad Grinding Noise, And Would Skip While Making Bread Dough

  • Customer: Dennis from Lake Mills, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 58 of 67 people found this instruction helpful
1, Removed trim piece (1 screw) 2, removed cover (4 screws) 3, removed speed switch assembly (2 screws) 4, removed gear cover (4 screws) 5, removed and examined 2 worm gears for wear. Gear cover was badly cracked, don"t know if it was caused by a previous repair or by heat, as old cover is plastic. Received new parts and installed them, 2 bearings, 2 worm... read more

Plastic gear housing in stand mixer fractured causing gears to crash

  • Customer: WES from BREVARD, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 58 of 79 people found this instruction helpful
Removed four screws to remove main cover. Removed four more screws to remove fractured plastic gear housing cover. Removed retainer ring and slid two gears and dowel off main shaft. Lifted out remaining gear train and bearings, Removed all grease and metal chips from all components. Greased new gears and reassembled. Replaced plastic gear housing cover... read more