466242414 Char-Broil Grill - Overview

This is a genuine Char-Broil replacement part, it is sold individually. This is the part of the Grill that the flame is coming from on your Gas Grill. Depending on your grill you may have 3 or 4 of these. To connect these to your grill, place the flat side of the Burner in the rear side of the firebox in the slots provided. The front of t...Read morehe burner will connect to the Electrode W/ Wire/Collector. They will connect to the Hose Valve Regulator, and then the Control Knobs will be attached, so the flame can be controlled. This part includes one threaded pin and one cotter pins.

This is a Genuine Manufacturer Approved Control Knob used on Char-Broil Gas Grills. It helps to control your Burners. This part is made out of Plastic and it is Sold Individually. Replacing this part does not require any tools, this Knob fits over the Regulator Shaft. Please note Bezel is Sold Separately.

This is an authentic Char-Broil replacement part. The cleaning tool is found in grills. This part is made of metal, and is an accessory used to scrape debris off of the infra-red emitter. No tools are required when replacing this item. This part is sold individually.

This is a genuine OEM replacement part for a Char-Broil Outdoor Stove. The grease tray is designed to catch grease drippings from food as it cooks. Before replacing this part make sure the stove is completely cooled down to avoid any possible injury. This part is made of metal with a grey powder coat finish. It is a separately sold replacement part.

This replacement part is specially designed for use with Char-Broil grills. It is an authentic OEM item, not an aftermarket equivalent. This carryover tube is used to carry the flame from one burner to another as well as supporting for the burners themselves. Over time tubes tend to rust in combination of heat and moisture requiring repla...Read morecement. Please note, this stainless steel tube is sold individually. This assembly includes two cotter pins to secure the carryover tube.

Genuine Manufacturer Sourced replacement part designed for some Char-Broil Grills. This part has a Plastic Body and it is Sold Individually. Igniter switch G515-0030-W2 produces the spark to ignite the burner. It has Two (2) Inputs and Five (5) output connectors. Requires an AA battery (not included).

This item is a genuine Char-Broil replacement part that is intended to be used with outdoor gas grills. The metal rail attaches to the bottom side of the firebox and is used to mount the grease tray to catch food drippings. The left rail is priced as a single replacement part.

This is an authentic Char-Broil replacement part and has been sourced from the original manufacturer to be used with commercial grills. The cast iron grates fit into the fire box above the burners and are used to support the food being cooked. This grate is priced as a single item. Approximate Measurements: Length 18.26" x Width 7.69"

This Emitter is sourced directly from Char-Broil and is an authentic OEM replacement part for Char-Broil grills.

An authentic manufacturer-sourced item that is specially designed for use with Char-Broil grills. This is one of the rails used to support the grease tray. It is a high-quality component which is made of durable metal and it is sold individually, please note the hardware to secure it is sold separately.

This locking caster is sourced from the original equipment manufacturer for use with outdoor grills. It consists of a wheel, with a diameter of 3 inches, and a metal bracket that allows for easy transportation and positioning. It also includes a locking mechanism that prevents unintentional movement of the grill. Over time, the caster may...Read more break, corrode, or fall out of alignment, thereby causing instability, failure of the locking system, and potential accidents. The caster will also need to be replaced if it is jammed or stripped. To replace a defective caster, prop the grill up and use a wrench or screwdriver to turn and remove the caster mounting bolt. Remove any dirt and debris in the area and align the new caster with the mounting hole. Turn the caster until it is firmly locked in place to complete the repair.