465R Husqvarna Chainsaw - Overview

Genuine Husqvarna replacement part, this part is sold individually. The 503939601 Air Purge does just what the part name says. It purges the air out of the carburetor. Then it forces fuel from the fuel tank and fuel line in to the carburetor.

Used to seal the fuel tank to prevent leaks and allow the fuel line to enter through it, this Fuel Tank Bushing is sourced directly from the manufacturer. It is made of black rubber, is not part of a kit or assembly, and is sold individually. This part will wear through regular use and should be replaced if you notice signs of damage or...Read more wear. When it malfunctions, you will see fuel leaking from the bushing. You will need a screwdriver and pliers to complete this repair. Customers rate this repair as Easy.

Compatible with over 150 models of lawn equipment, this Spark Plug has been sourced directly from the original manufacturer. It is sold individually, made of metal and ceramic components, and is not part of a kit or assembly. The spark plug is used to ignite the air-fuel mixture inside the combustion chamber. You may need to replace the...Read more Spark Plug if your 1 cylinder engine won't start, or if your more-than-1 cylinder engine runs rough. Spark Plugs will wear over time and should be inspected regularly. Customers rate this repair as Easy.

This fuel tank bushing grommet creates a tight seal where the fuel line enters the tank, helping prevent leaks and keep air and debris out of the fuel system. Made from durable, fuel-resistant rubber, it supports reliable engine performance and consistent fuel flow. Replacing a worn or damaged grommet can help eliminate leaks and restore proper operation.

Genuine OEM Husqvarna replacement part, this item is sold individually. This screw is used to secure the Starter Housing on the Husqvarna Chainsaws. Use a Flat head Screwdriver or a Hex Key to tighten or loosen the screw.

Designed for use in various chainsaws, the E-Ring secures the pivot pin, which holds the handguard. It is an authentic OEM replacement part made of durable black metal and sold individually, not as part of a kit or assembly. When this part malfunctions, you may notice the handle or handguard is loose. At which point, it will need to be ...Read morereplaced. To complete this repair, you will need a pair of pliers. Customers rate this repair as Easy.

This is a genuine Husqvarna replacement part, it is sold individually. The Fuel Filter is inside of the fuel tank. Its purpose is to filter out dirt and other debris from contaminating the carburetor. It will at sometime become clogged and restrict the fuel getting to the carburetor,and will have to be replaced. We do have an article an...Read mored video on How to Replace the Fuel Filters in Your Outdoor Power Equipment.. You can see this by going to the front page of our site and clicking on Repair Center.

This check valve, also known as a one-way valve, is a genuine OEM part that regulates the flow of fuel/oil in the equipment engine to prevent it from flowing backwards. It is made of plastic and designed for use in a variety of lawn and garden power equipment. If the valve is jammed, worn down, or contaminated with dirt and debris, it wil...Read morel be unable to open and close properly, thus restricting the flow of fuel and compromising the engine combustion process. You will likely notice fuel leaks around the carburetor, engine stalling, hard starting, and overall lower performance from your equipment. To remove the faulty valve, carefully disconnect any hoses or fasteners connected to it. Place the new valve in position and secure it appropriately.

This authentic OEM rim sprocket in your chainsaw transfers power from the engine to the cutting chain. It is typically located at the center of the clutch drum, situated at the end of the engine crankshaft. By engaging with the chain drive links, it enables the chain to rotate and cut through materials as the engine turns. You will notice...Read more that if the rim sprocket is broken that the chain slips, does not engage, or rotates unevenly. It may also reveal signs of wear such as worn-out teeth. Failure to replace a broken rim sprocket can result in reduced cutting power, chain damage, and increased strain on the engine. To remove the rim sprocket, first, loosen the chain tension by adjusting the tensioning screw or knob. Then, remove the guide bar by loosening the nuts or clips on the side cover and sliding the guide bar off the saw. Use a screwdriver or appropriate tool to remove the screws or fasteners securing the clutch cover. With the clutch cover removed, you can access the clutch drum. Hold the drum in place and turn the retaining bolt counterclockwise to loosen it. Carefully slide off the clutch drum. This replacement part is sold individually.

Primarily used in chainsaws, this Starter Rope is an exact replacement part for hundreds of models. It is white and sold individually, not as part of a kit or assembly. The Starter Rope will need to be replaced once you notice signs of it fraying, wearing, or it breaks off. Customers rate this repair as Easy.

This M8 flange nut secures the guide bar and chain assembly in place, ensuring proper alignment and safe operation of your equipment. Designed with an integrated flange and anti-slip teeth to resist loosening from vibration, it provides a reliable, secure hold during heavy use. Made from durable, corrosion-resistant steel with an M8 threa...Read mored and 1.25?mm pitch, replacing a worn or missing nut helps maintain stability and dependable performance.

This screw is an authentic OEM part which made for Husqvarna chainsaws. It is designed for multiple uses based on your tool. Please refer to diagrams for correct location and applied use of this screw. It includes one (1) metal screw per order. This is a hex head item so you would need a hex key/allen wrench to install or remove it.