4648 Char-Broil Grill - Overview

This replacement grease cup is specially designed for use with Char-Broil grills. It is an authentic item that is sourced directly from original equipment manufacturer. The purpose of this tray is to collect the grease and other food particles from the food you are cooking. After each use it is recommended to clean this part with soap and...Read more water to avoid rusting. This item is made out of metal and it is sold individually. Please note, the grease cup clip/holder is sold separately.

This vaporiser bar is a genuine Char-Broil replacement part. It is supplied from original equipment manufacturer for use with gas grills. Bars are designed to redirect grease away from the burner tubes. This would greatly cut down on flare ups. An extra benefit of these bars is that they help add extra flavor to your food. Unfortunately, ...Read moreover time bars might begin to rust due to a combination of heat and moisture. This metal vaporizer bar is sold individually.

This is a Genuine Manufacturer Approved replacement Burner designed for Char-Broil Grills. This part is made out of Stainless Steel and it is Sold Individually. This is the Part that the flames rise from and allow grill temperature to be properly maintained. This Round burner used in sets of two or three depending on grill model. Ignito...Read morer electrode is included in this Assembly and it comes already mounted on the rear of the burner. No special hardware is required to replace this Burner, simply slide it on the Nozzle of the Valve Assembly.

This is an individual plastic wheel compatible with various models of outdoor grills. This wheel attaches to an axle rod at the bottom of the grill assembly, allowing you to move it around. If you find your grill difficult to move and notice that the wheel(s) do not rotate or move smoothly due to damage or warping, you will need to replac...Read moree this wheel. Consider ordering multiple wheels if you find that more than one is not moving properly. This wheel measures approximately 6 inches in diameter and has a 1 1/16-inch outer diameter and 3/8-inch inner diameter bearing. To replace this wheel, you only need to remove the pin that secures it to the axle rod. Then, you can slide off the old wheel and install and secure the new wheel in place.

This is an OEM replacement part sourced directly from Char-Broil for use with a gas grill. The purpose of a vaporiser bar is to distribute the heat evenly and prevent grease drippings from reaching the burner tubes which prevents flare-ups. Unfortunately, over time the vaporiser bar will rust and require replacement. This part is made of a high-quality metal and is sold separately.

This replacement heat tent is an authentic OEM sourced item that is designed for Char-Broil gas grills. It is secured over the burner tube to direct grease and drippings away which will help to cut down on flare ups tremendously. An extra benefit of these tents is that they help to add that "cooked on a grill" flavor to your food by vapor...Read moreizing the grease. Because tents tend to rust in the combination of heat and moisture they should be cleaned every time after each use with warm water and soap. This item is made from durable steel with porcelain coating and it is sold individually.

The electrode is made of metal and helps to light the burner. This item is available as an individual replacement part. A screwdriver and a socket set might be needed during the installation process. It will need to be replaced if it breaks. This is an OEM replacement part for use in Char-Broil grills.

This is an authentic Char-Broil replacement part manufactured for use with outdoor grills. The metal grease cup clip fits onto the underside of the cook box and is used to hold the grease cup which collects cooking drippings. The grease cup clip is sold individually.

This replacement button is a genuine OEM supplied item that is specially produced for Char-Broil grills. It is used to secure the battery in the electronic ignition module. Please note this item includes one black plastic button with a metal spring.

This replacement temperature gauge is specially designed for use with Char-Broil grills. It is an authentic OEM sourced item, not an aftermarket equivalent. This gauge is used to measure the temperature inside the grill. This part is made from durable metal and it is sold individually. Please note, the wing-nut and the washer to secure it are both included in this assembly. Dial reads 50 - 700 degrees.

This is a genuine manufacturer-sourced component which is specially made for use with Char-Broil grills. It is an identical replacement for a missing or a faulty collector box twist lock that was installed on a new unit. This is the part that helps to lock the collector box. Please make sure to refer to the appropriate diagrams of your mo...Read moredel for the correct location and application of this part. Keep in mind this high-quality component is made of durable metal and is sold individually.