463724 Char-Broil Grill - Overview

This replacement grease cup is specially designed for use with Char-Broil grills. It is an authentic item that is sourced directly from original equipment manufacturer. The purpose of this tray is to collect the grease and other food particles from the food you are cooking. After each use it is recommended to clean this part with soap and...Read more water to avoid rusting. This item is made out of metal and it is sold individually. Please note, the grease cup clip/holder is sold separately.

This is a genuine Char-Broil replacement part manufactured for use with outdoor grills. The plastic control knob fits onto the gas valves, and it used to open and close the valve. The control knobs are sold individually.

This is a genuine OEM replacement parts designed for use with Char-Broil grills. The purpose of a heat tent is to direct grease and drippings away from the burner tubes, which cuts down on flare ups tremendously. An extra benefit of these tents is that they help to add that "cooked on a grill" flavor to your food. Tents tend to rust is th...Read moree combination of heat and moisture and should be replaced if they are damaged or lost. This item is made out of steel with porcelain coating and it is sold individually. No tools needed to replace.

It is an authentic OEM supplied replacement item that is specially produced for use with Char-Broil grills. This is the clip that helps to secure the grease cup which is sold separately. Please note this durable metal item is sold individually.

This is an individual plastic wheel compatible with various models of outdoor grills. This wheel attaches to an axle rod at the bottom of the grill assembly, allowing you to move it around. If you find your grill difficult to move and notice that the wheel(s) do not rotate or move smoothly due to damage or warping, you will need to replac...Read moree this wheel. Consider ordering multiple wheels if you find that more than one is not moving properly. This wheel measures approximately 6 inches in diameter and has a 1 1/16-inch outer diameter and 3/8-inch inner diameter bearing. To replace this wheel, you only need to remove the pin that secures it to the axle rod. Then, you can slide off the old wheel and install and secure the new wheel in place.

This replacement heat tent is designed for use with gas grills. It is supplied directly from original equipment manufacturer. The heat tent is used to direct the grease and drippings away from the burner tubes. This will help to greatly reduce flare ups and add that "cooked on a grill" flavor to your food. Tents would normally rust in the...Read more combination of heat and moisture. If a tent is damaged or lost it should be replaced. This item is made out of steel with porcelain coating and it is sold individually.

This is an authentic Char-Broil replacement part sourced from the original manufacturer, not an aftermarket imitation part. This metal vaporiser bar fits above the burners, and disperses the heat from the flame, and protects the burner from drippings. The vaporiser bar is sold individually. Measurements • Length 23 1/2", Width 2 9/16"

Grease Tray

This is an authentic Char-Broil replacement part, sourced from the original manufacturer for use with outdoor gas grills. The metal grate fits into the fire box above the burners and is used to support the food while cooking. This item is available as an individual replacement part, please not four grates may be required. Approximate dimensions: • Length 19.13" x Width 10.03"

This is a genuine Char-Broil replacement part, sourced from the original manufacturer for use with outdoor grills. The bumper is silicone rubber, and used on the main lid. This bumper protects the lid and burner box from damage when closing the lid. The bumper is sold individually.

This is an OEM replacement part for Char-Broil combination charcoal-gas grills. The main burner is used to distribute gas and flame evenly throughout the grill. A screwdriver will be needed to install or replace the main burner. This part is made of stainless steel and is sold individually.

This charcoal pan is a durable metal tray designed for select hybrid gas-and-charcoal grills, providing a stable surface to hold charcoal beneath the cooking grates. It allows you to enjoy charcoal grilling while using the gas burners for quick and easy ignition, helping reduce flare-ups and creating consistent heat. Sized to fit specific...Read more multi-fuel grill models, it serves as a direct replacement when the original pan becomes worn or damaged, restoring proper grilling performance.