The run capacitor helps the compressor kick on and off while maintaining a constant temperature in your fridge and freezer. You may need to replace your run capacitor if your refrigerator or freezer section will not start, if they are too warm, or if your refrigerator has become too noisy. Replacing the run capacitor is a relatively easy ...Read moreproject. For this repair you will only need a 1/4 inch nut driver and needle nose pliers. Remember to disconnect the power and water supply line to the unit before you begin this repair. For full step by step instructions, simply click on the video below.
This gasket retainer clip kit is for freezers. There are 24 pieces in this kit. The clips are what secure the gasket and liner to the freezer lid. The clips are white in color and made of plastic. If you notice frost build up in your freezer or that is it is not maintaining its temperature, this might be because the retainer clips have br...Read moreoken, and this has caused the gasket to become loose. This is a genuine OEM part that is obtained right from the manufacturer, ensuring a quality repair.
This is not the handle. This is the decorative front insert. This part is for your freezer and is white in color. The insert measures approximately 10 inches long. This part is often replaced along with the handle itself. If this part has broken, cracked, or fallen off, it may need to be replaced after repeated use. To install the new han...Read moredle insert, you must simply pry the old one off and snap the new one into place; no tools required. This is an original OEM part that comes right from the manufacturer.
This is a shelf support for the left side of a freezer. It is used to help support the inside of the shelf from both sides. *Please note: right and left side of shelf support are sold separately. If the shelf in your fridge is unstable, replacing this part could be the solution. Make sure to unplug the refrigerator or freezer from the pow...Read moreer source before beginning this replacement project and safely store food. Follow the instructions in the diagram provided by the manufacturer for further instructions and guidance.
This is a plastic OEM drain plug that is attached to the drain system of your appliance and is compatible with several different makes and models of refrigerators, freezers, and air conditioners. This drain plug is used to prevent water from leaking out of the incorrect drain system within the appliance and is normally removed for cleanin...Read moreg and maintenance. If you notice water leaking inside of your appliance, the plug may be improperly positioned or may need replacing. To replace, simply pull off the damaged plug and insert the new plug in its place.
A filter-drier in a refrigerator has two essential functions. The first is to absorb system contaminants, such as water, which can create acids. The second is to provide physical filtration. This means trapping moisture, small metal chips, and dirt found in the refrigerant gas. If your refrigerator motor is constantly running, but the ref...Read morerigerator is not getting cold, the issue could be due to a damaged or faulty filter-drier. Faulty filter-driers are sometimes the cause for abnormal freezer compartment temperatures and partially frosted evaporators. This filter-drier is approximately 11 inches long. Remember to disconnect the power from your refrigerator before beginning this repair.
This part is found in freezers. The stud may have broken over time and may no longer be supporting the shelf. If your shelf is not staying in place or you are not able to adjust heights, it may be due to the support being broken. To complete this repair, you will need to open the fridge and remove the drawer and the shelf. To remove the o...Read moreld stud, you will need a 3/4-inch wrench to twist it off. The new part should push into place and will need to be turned with your wrench to be secured into place.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
just quit working
19 of 25 peoplefound this instruction helpful.
Denise from Lowell, MI
Really Easy
Less than 15 mins
Bought a new capacitor.
Was this helpful?
Thank you for voting!
Refrigerator was not cooling
17 of 24 peoplefound this instruction helpful.
Vicki from Johnson City, TX
Really Easy
Less than 15 mins
This was a simple job. Raised the flap in the back that houses the compressor, removed the wire that holds the relay, pulled out the old relay and pushed the new one on. Replaced wire holder and that was it. Plugged it frig and freezer is at zero and lower compartment at 35. As easy as brushing your teeth!
Was this helpful?
Thank you for voting!
Refrigerator quit running
23 of 43 peoplefound this instruction helpful.
Frederic from Daytona Beach, FL
Really Easy
Less than 15 mins
I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I
... Read moredo hope this is normal in this model? anyway it runs fine mow. Thank you.