41ADC47C712 Cub Cadet Trimmer - Overview

The Fuel Pick Up Line with Filter is an OEM plastic part used to filter and deliver fuel to the carburetor. If broken, the engine will not get fuel and the part should be replaced. This part is rated "Easy" to install and only requires a set of pliers.

The Fuel Return line is a blue plastic tube which attaches to the purge bulb and fuel tank in order to return fuel back to the tank after the primer bulb is pressed. It is rated "Easy" to install and requires pliers and a screwdriver.

Genuine OEM replacement part, this item is sold individually. The 791-181459 Spring is installed in the 753-04257 slider. When not activated this part will keep the cutting line from coming out of the spool. When the Bump Head Knob Assembly is hit on the ground the springs and slider will be forced up into the spool housing releasing the ...Read morecorrect amount of cutting line. Most of the trimmers will use two of these springs.

This is a foam air filter designed for use within various models of outdoor power equipment like trimmers and leaf blowers. This foam filter measures approximately 3-inches in length and fits within the air filter assembly to prevent contaminants from entering your equipment. Air filters commonly build up with dust and dirt over time, and...Read more will need to be replaced every so often, and regularly inspecting them for build ups can reduce the amount of extra maintenance that is required. If your air filter is clogged, it will lead to worse performance from your equipment, like difficulty starting or not starting at all, and can even damage the carburetor and engine. To replace the air filter, remove the cover for the air filter housing, and remove and dispose of the old filter. Rub a small amount of oil into the new filter before installing it and securing the air filter cover.

Genuine OEM replacement part, this item is sold individually. The 753-04257 Slider is part of the cutting string release system for the Trimmers listed below. If your trimmer is not releasing the cutting line properly check this part for wear and all of the other parts associated with it.

This is a genuine replacement part from original manufacturer. It is compatible with Ryobi, MTD, Troy-Bilt, Yard Man, and Bolens machines. It\\\'s used with a variety of power tools including trimmers, tillers, and blowers. O-rings create a seal between solid parts, retaining pressure. Because many machines use more than one type of O-rin...Read moreg, use care to ensure that the right one is being used in the right spot. This ring is sold individually.

This is a genuine manufacturer approved replacement mulching door torsion spring designed for use with handheld trimmers/edgers. This spring helps the throttle trigger to retract. It is made out of metal and it is sold individually. Replacing this item you would need a screwdriver and pliers.

The metal spring goes between the e-clip and the plunger and helps to maintain tension. It is a genuine item that is supplied by the original equipment manufacturer for use with trimmers. This is a small part that will need to be replaced if it becomes lost or stretched and may require a screwdriver to install the spring. This is available as an individual replacement part.

It is an authentic OEM sourced part which is made for use with handheld trimmers. This is the special component which provides a tight fit for the outer spool. Unfortunately, over time the hardware may get damaged or lost eventually requiring a replacement. One durable metal retainer is included. Refer to the appropriate diagrams for your...Read more model for the exact location and the correct application. You may need snap-ring pliers to perform this repair.

The Recoil Spring is a silver, metal spring which attaches inside the starter assembly. It is used to wind the rope back around the pulley after it has been pulled. If broken, the starter rope will not retract and the part must be replaced. This spring is rated "Medium" difficulty to install and will requires a screwdriver, pliers and a wrench set.

The Clutch Drum is a silver, metal part used to transmit power from the engine to the drive shaft. Installation is rated "Medium" difficult and will require a screwdriver, wrench set, and torx wrenches. This part attaches to the clutch assembly. If broken, the clutch will slip and you will lose drive power. If this happens, the part must be replaced.