41AD890A734 Ryobi Trimmer - Overview

This plastic throttle trigger measures 2.5-inches in length and controls the power, speed, and intensity of the motor for your lawn equipment through the throttle cable and carburetor it is attached to. Sold as an individual part without any securing hardware, this trigger, although made of durable plastic, is a high-use part that will ne...Read moreed to be replaced more often than other parts. Check the user manual for your model for exact placement and installation location of this trigger.

The Fuel Pick Up Line with Filter is an OEM plastic part used to filter and deliver fuel to the carburetor. If broken, the engine will not get fuel and the part should be replaced. This part is rated "Easy" to install and only requires a set of pliers.

The Fuel Return line is a blue plastic tube which attaches to the purge bulb and fuel tank in order to return fuel back to the tank after the primer bulb is pressed. It is rated "Easy" to install and requires pliers and a screwdriver.

This is a foam air filter designed for use within various models of outdoor power equipment like trimmers and leaf blowers. This foam filter measures approximately 3-inches in length and fits within the air filter assembly to prevent contaminants from entering your equipment. Air filters commonly build up with dust and dirt over time, and...Read more will need to be replaced every so often, and regularly inspecting them for build ups can reduce the amount of extra maintenance that is required. If your air filter is clogged, it will lead to worse performance from your equipment, like difficulty starting or not starting at all, and can even damage the carburetor and engine. To replace the air filter, remove the cover for the air filter housing, and remove and dispose of the old filter. Rub a small amount of oil into the new filter before installing it and securing the air filter cover.

This is a genuine replacement part manufactured for use with trimmers. The kit includes the metal retaining washer which is used with the blade, and spool cutting heads. The kit also includes the nut that fastens the blade to the gearcase, the kit is sold individually.

This is a genuine replacement part from original manufacturer. It is compatible with Ryobi, MTD, Troy-Bilt, Yard Man, and Bolens machines. It\\\'s used with a variety of power tools including trimmers, tillers, and blowers. O-rings create a seal between solid parts, retaining pressure. Because many machines use more than one type of O-rin...Read moreg, use care to ensure that the right one is being used in the right spot. This ring is sold individually.

This is a genuine OEM replacement part. it is sold individually. The Bump Head Knob Assembly is the part of the trimmer that you bump on the ground to advance the cutting line from the spool. Because of the abuse this part gets, it is advisable to order an extra one so you have on on hand. LEFT HAND THREADED

This is a genuine replacement part is designed for use with handheld trimmers. It is sourced from original manufacturer and it is sold individually. This split boom coupler includes metal coupler, knob and screws needed to fasten the upper shaft housing to the lower boom assembly. To complete this repair you would need a phillips head screwdriver.

This is a genuine manufacturer approved replacement mulching door torsion spring designed for use with handheld trimmers/edgers. This spring helps the throttle trigger to retract. It is made out of metal and it is sold individually. Replacing this item you would need a screwdriver and pliers.

The Recoil Spring is a silver, metal spring which attaches inside the starter assembly. It is used to wind the rope back around the pulley after it has been pulled. If broken, the starter rope will not retract and the part must be replaced. This spring is rated "Medium" difficulty to install and will requires a screwdriver, pliers and a wrench set.

The Clutch Drum is a silver, metal part used to transmit power from the engine to the drive shaft. Installation is rated "Medium" difficult and will require a screwdriver, wrench set, and torx wrenches. This part attaches to the clutch assembly. If broken, the clutch will slip and you will lose drive power. If this happens, the part must be replaced.

This is a genuine item that is supplied by the original equipment manufacturer for use with trimmers. The metal clutch goes between the clutch drum and the clutch washer. It helps to spin the cutting head and the flex shaft. It may require a screwdriver and a hammer for installation. This clutch is available as an individual replacement part and comes with a washer.