This is a 120 volt, 60 hertz drain pump assembly for a washing machine. It is a genuine OEM part. This pump helps expel water from the washing machine, and is activated after the spin speed is maintained for a specific period of time during the spin cycle. You may need to replace the pump assembly if your washer is not draining properly; ...Read moreit could be clogged or damaged. Be sure to disconnect the water supply and power to your appliance before repairing. This part is located at the rear of the washer behind the back panel.
This part is used for the shaft on the rear of the tub and is sold individually. The head bolt is part of the spider arm assembly, and they are generally changed at the same time. If you are replacing the entire spider arm assembly, make sure you order as many hex bolts as you will need. The spider arm assembly contains 6 of these hex bol...Read morets. The hex bolt or spider arm assembly may need to be replaced if you notice that your inner tub is going out of balance. The hex bolt measures 1.5 by 0.5 inches.
This is an outer seal clamp for the washer door boot of your Samsung washing machine. This clamp tightly seals the boot of the drum within the door of the washer to prevent leaks. This clamp is made of metal and features a spring in the middle, but over time can be worn down or break, and result in water leaking out of the washing machine...Read more and into your home. Replacing this clamp will require a screwdriver, pliers, and safety gloves. This clamp is an OEM part that comes individually, without any other parts or accessories.
This is a door diaphragm, also commonly known as a door boot seal, for a washer. The boot is fitted between the washer door and the tub to prevent leaking while the appliance is in use. It is made of rubber and is gray in color. Your boot can tear if the washer is overloaded. Alternatively, age and detergents can wear and dry out the boot...Read more which causes it to become brittle and weak. This may cause your washer to leak, and you may need to replace the boot. This is an authentic replacement part from the original manufacturer.
Shipping bolts are installed through the back of the washing machine, and hold the wash tub and basket in place while your washer is being transported. The tub suspension holds the tub correctly in place during the wash, rinse, and spin cycles. If this suspension is damaged during shipping, the tub can shake and move, tilt to one side, or...Read more spin incorrectly. This could lead to the suspension or motor failing. When moving your washer, it is suggested that you insert the shipping bolts back into place before moving the machine. This part is also called a washer transit bolt. Remember that this part is sold separately, and to check your model to see how many you require.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Roger - For model number 40249032010
July 13, 2021
I'm getting an nd error on the screen, what does that mean?
Hello Roger, Thank you for the question. The ND stands for Not Draining. If the drain hoses are all clear, you may have a defective Drain Pump. We hope this helps!
I am trying to figure out all the pieces that stabilize the tub and keep it in place but I don’t see a diagram that specifically shows it. It looks like there are 4 shock absorbers for the bottom but anything on the top besides the springs?
Hello Christopher, thank you for the question. According to our research, we would recommend checking the following parts to fix your issue: spring, part number PS4206209, shock damper rear, part number PS4212251, and shock damper front, part number PS4212221. If you need help placing an order for it, please feel free to give us a call. We look forward to hearing from you!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Code indicating washer was NOT discharging water
11 of 17 peoplefound this instruction helpful.
SCOTT from VERNAL, UT
Easy
30 - 60 mins
Pliers, Screw drivers
Watched the video, procedure was simple and as depicted on the video. Started by using a wet shop Vac to the discharge hose and sucked as much dirty wash water out as possible. Removed the pump,and found the motor did not turn freely. Removed the motor (3 screws) and replaced the motor with new part. Reassembled the washer, everything wor
... Read moreked as it should. After about 3-4 loads of laundry, the "Not Draining" code / problem returned. Again, sucked out the water with the Shop Vac. Checked the Filter /Cleanout and found it completely packed with MUD. Cleaned that out, and again disassembled the washer. The pump was removed and the remaining muddy gunk was cleaned from the impeller. The 3 drain lines that attached to the pump were inspected for blockage/obstruction and flushed of any muddy residue. Reassembly was quick and easy, and the washer has worked well since. I have no idea how the dirt got into the system with enough dirt to gunk up the system. Recommend keeping more frequent inspections of the cleanout trap.
Read less
Was this helpful?
Thank you for voting!
OE error code, water keeps flowing during spin cycle, softener dispenser left half full of water, clothes wet after washer stops
3 of 3 peoplefound this instruction helpful.
Gary from Peachtree City, GA
Really Easy
15 - 30 mins
Screw drivers
Found a repair video of a Samsung washer that looks like mine (9 years old). Removed two screws from the back of the washer, slid the top a few inches toward the front and lifted it off. Disconnected the two double electrical connections, the two rubber tubes from the solenoids, the cold water hose from the back and removed the two scre
... Read morews holding the valve in place. Installed the new valve by reversing those steps, slid the top back into place and secured it with the two screws and viola (as Kelly Bundy would say)! The washer now functions normally. I'm waiting for my next water bill to arrive to see whether the sudden increase in usage decreases to its normal amount. We have three adults and four small children in the household so the washer is constantly in use.
Read less
Was this helpful?
Thank you for voting!
The drain check valve leaked
1 personfound this instruction helpful.
scott from DEERFIELD, OH
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers, Socket set
The part did not fit this model. The flap part fit the hole but the seal ring is too big. I cut 1\4inch out and used super glue the make it small enough to fit and seal the hose. Make sure you only use a drop of glue and keep the seal even and flat so it will seal
My Orders
