This part is used for the shaft on the rear of the tub and is sold individually. The head bolt is part of the spider arm assembly, and they are generally changed at the same time. If you are replacing the entire spider arm assembly, make sure you order as many hex bolts as you will need. The spider arm assembly contains 6 of these hex bol...Read morets. The hex bolt or spider arm assembly may need to be replaced if you notice that your inner tub is going out of balance. The hex bolt measures 1.5 by 0.5 inches.
This is an outer seal clamp for the washer door boot of your Samsung washing machine. This clamp tightly seals the boot of the drum within the door of the washer to prevent leaks. This clamp is made of metal and features a spring in the middle, but over time can be worn down or break, and result in water leaking out of the washing machine...Read more and into your home. Replacing this clamp will require a screwdriver, pliers, and safety gloves. This clamp is an OEM part that comes individually, without any other parts or accessories.
This is the drain pump assembly for various models of Samsung washing machines. The drain pump is used to remove any water from the washer after it has completed its washing cycle. If your washer still has water left in the tub after it has finished washing this drain pump assembly is likely bad defective or worn out and in need of replac...Read moreing immediately. It is important that you do not use your washer with a bad drain pump as that could lead to further damage to your washer clothes or home. This drain pump assembly is approximately 4.5 inches tall and will require tools such as a wrench and screwdriver to access and replace. This drain pump is sold as an individual OEM part and does not include any securing screws.
Shipping bolts are installed through the back of the washing machine, and hold the wash tub and basket in place while your washer is being transported. The tub suspension holds the tub correctly in place during the wash, rinse, and spin cycles. If this suspension is damaged during shipping, the tub can shake and move, tilt to one side, or...Read more spin incorrectly. This could lead to the suspension or motor failing. When moving your washer, it is suggested that you insert the shipping bolts back into place before moving the machine. This part is also called a washer transit bolt. Remember that this part is sold separately, and to check your model to see how many you require.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
OE error code, water keeps flowing during spin cycle, softener dispenser left half full of water, clothes wet after washer stops
3 of 3 peoplefound this instruction helpful.
Gary from Peachtree City, GA
Really Easy
15 - 30 mins
Screw drivers
Found a repair video of a Samsung washer that looks like mine (9 years old). Removed two screws from the back of the washer, slid the top a few inches toward the front and lifted it off. Disconnected the two double electrical connections, the two rubber tubes from the solenoids, the cold water hose from the back and removed the two scre
... Read morews holding the valve in place. Installed the new valve by reversing those steps, slid the top back into place and secured it with the two screws and viola (as Kelly Bundy would say)! The washer now functions normally. I'm waiting for my next water bill to arrive to see whether the sudden increase in usage decreases to its normal amount. We have three adults and four small children in the household so the washer is constantly in use.
Read less
Was this helpful?
Thank you for voting!
The boot had a crack, where the leak was.
1 of 3 peoplefound this instruction helpful.
Hilda from YONKERS, NY
Easy
30 - 60 mins
Pliers, Screw drivers, Socket set
Took off the front part of boot on the door, continued to take out the front and top off to washer Faisal. Removed weights and boot connected to the drum. Installed new boot and leeks was gone.
Was this helpful?
Thank you for voting!
The water level was lower than normal.
3 of 10 peoplefound this instruction helpful.
Fredric from ROCKMART, GA
Really Easy
15 - 30 mins
Pliers, Screw drivers
First unplug or turn off thee circuit breaker. Then remove the two screws to the top cover. Slide the cover back about three inches then remove the cover. Next take out the screw to the old sensor. Then unplug the electrical connection by squeezing and the pulling to disengage. Now set the old unit aside. You then grad your eight inch wi
... Read morere tie and hold the with flat side to the right and just to the right of the screw hole for the bracket is a square hole. Feed to wire tie into the square hole with your left hand then loop down left side of the end of new sensor and back up threw the square hole and tighten with the pliers. Your new sensor will be positioned just like it was mounted to the metal bracket. And pretty ridged. Now connect the vacuum hose and electrical connector.