Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 3XART710GW00

3XART710GW00 Whirlpool Refrigerator - Overview

Get Parts and Repair Help for 3XART710GW00

If you know the refrigerator repair part you need, you can browse the list of all parts on the 3XART710GW00, or you can search by name or part description. You can also find your part by where it is located on the 3XART710GW00 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for 3XART710GW00 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Manuals & Care Guides for 3XART710GW00

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$56.96

Crisper Drawer with Humidity Control

The crisper drawer with humidity control is also known as the crisper drawer, and it is an easy part to replace in your refrigerator. The crisper drawer is found at the bottom of t...

$5.48

Lower Door Closing Cam

The lower door closing cam is designed for use with refrigerators. It can be used on either the fresh food side, or the freezer side. It helps raise the door into position so the door can seal properly when closed. It also allows the door to easily swing open and closed. This cam is made out of plastic, so it might crack or wear down over time. If your door will not open and close properly you may need to replace a door closing cam. To successfully install this part, you will need a 5/16 nut driver and a small flat blade screwdriver. Before you begin, unplug your appliance and disconnect the water supply. This replacement part is sold individually.

$4.74

Door Cam - Black

The lower door cam is also known as the closing cam or door closer cam and can be found on your refrigerator or freezer door. The purpose of the lower door cam is to lift the door ...

$13.30

Control Bracket

This is a control bracket for your refrigerator, and may also be known as the dispenser control bracket. The function of this part is to be used as a fastener to hold the micro switches and the light socket in the freezer dispenser section in place. Its measurements are roughly 9 inches long and 5 inches high, and this model comes in white. The tools you will need in order to make this installation include a Phillips screw driver, a quarter-inch nut-driver, and a pair of needle-nose pliers. If your ice dispenser is not working properly, your bracket could be the problem.

$8.64

Ice Guide

This is a refrigerator ice guide that is made entirely of clear plastic. This ice guide is located in the freezer door. Turn your refrigerator ice dispenser off before replacing th...

$23.78

Bi-Metal Defrost Thermostat

If you have ice building up in your freezer, or if your freezer is getting too warm during the defrost cycle you may need to replace the bi-metal defrost thermostat. The function of the defrost bi-metal thermostat is to clip onto the evaporator and protect your evaporator from overheating during the defrost cycle. If your refrigerator does not defrost properly you can test both the thermostat and the heater to figure out which part is at fault. For this repair, you will need a Phillips screwdriver, a 1/4 inch nut driver, a flat blade screwdriver, a pair of wire strippers, a roll of electrical tape, and a few butt splice connectors.

$53.91

Ice Door Kit

In this kit you will find the support, the ice door, spring, and delay. The heater ribbon is no longer needed and therefore will not be included with this part. This kit works in t...

$2.96

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.

$29.94

Ice Bin Auger Drum

This white ice bin auger drum comes with a washer.

$5.21

Icemaker Water Fill Tube Kit

The icemaker water fill tube provides water to the icemaker so it can produce ice and dispense water. If you notice that your ice maker is not making or dispensing ice, or is leaking, you may need to replace the water fill tube. This water fill tube kit comes with a fill tube and a compression nut. This part is made of white plastic and is approximately 10 inches in length. The ice maker water fill tube is in the rear of the fridge. To complete this repair, you will need a 1/4 inch nut driver and a utility knife. Before beginning this repair, you may want to disconnect the water and power supply to the refrigerator.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Front Door Ice Wouldn't Work And Air Going Into Freezer

  • Customer: BILL from BATESVILLE, MS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 461 of 537 people found this instruction helpful
Thanks to the pictorial diagram, I was able to order correct parts. It was just a matter of removal of broken parts and replacing them. Ice maker now working and air is no longer getting into freezer which was freezing up ice maker. Thanks for timely delivery, now I am able to use ice dispenser, which I haven't used for long time. Thanks read more

track of the pan become broken

  • Customer: Darrell from Cedar Bluff, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 417 of 429 people found this instruction helpful
Buy a new crisper pan,slide out old one ,slide in new one read more

Refigerator door was not closing all the way if not pushed shut.

  • Customer: Norbert from Sugar Land, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 292 of 298 people found this instruction helpful
Remove the top hinge cover. Removed the top hinge support. Lifted the door from the bottom support. Old door cams were worn completly flat. Replaced the lower door cam and closing cam use a little vasalene for lubricant on the cam surfaces. Placed the door back on the lower hinge support. Replaced the top hinge support. Door is closing great now. read more