This is a genuine Husqvarna replacement part, it is sold individually. The Fuel Filter is inside of the fuel tank. Its purpose is to filter out dirt and other debris from contaminating the carburetor. It will at sometime become clogged and restrict the fuel getting to the carburetor,and will have to be replaced. We do have an article an...Read mored video on How to Replace the Fuel Filters in Your Outdoor Power Equipment.. You can see this by going to the front page of our site and clicking on Repair Center.
This screw is an authentic high-quality item that is specially produced for Husqvarna and Poulan handheld lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please refer to appropriate diagrams for the correct location and use of this screw. Please note this high-quali...Read morety hardware is sold individually, keep in mind you will need an Allen wrench also known as a hex key to secure or remove it.
Primarily used in chainsaws, this Starter Rope is an exact replacement part for hundreds of models. It is white and sold individually, not as part of a kit or assembly.
The Starter Rope will need to be replaced once you notice signs of it fraying, wearing, or it breaks off.
Customers rate this repair as Easy.
This screw is an authentic OEM part which made for Husqvarna chainsaws. It is designed for multiple uses based on your tool. Please refer to diagrams for correct location and applied use of this screw. It includes one (1) metal screw per order. This is a hex head item so you would need a hex key/allen wrench to install or remove it.
This fuel pump diaphragm, also called a membrane or a gasket, is what helps pump fuel from the tank to the engine of your gas-powered lawn equipment. It is normally found attached to the carburetor assembly itself. You can tell that the diaphragm is broken when your engine is not starting properly, lacks power, or frequently stalls. You m...Read moreay also notice that your machine is leaking fuel or smells strongly of gasoline. A broken diaphragm could lead to engine performance problems, and it may eventually stop working altogether. When replacing your old diaphragm, you will need a wrench to disconnect it from the fuel pump housing. Kindly note that this OEM-sourced component is sold individually.
This part is an OEM sourced directly from the manufacturer. It is intended to be used in chainsaws and brushcutters made by Husqvarna and Jonsered. The impulse pipe attaches to the bulkhead assembly next to the intake sleeve. This is a small rubber part and will need to be replaced if it becomes lost. The pipe is available as an individual replacement.
This is an original Husqvarna replacement part manufactured for use with chainsaws. Some ignition models do not include the spark plug connector also called a spark plug boot, it is recommended to inspect the spark plug boot or replace it when servicing the ignition module. The rubber spark plug connection kit includes the coil spring. Th...Read moree coil spring has a sharp end that pierces the insulation of the ignition module\'s wire, and it is the coil spring that makes contact to the wire. This spark plug connection kit is sold individually.
This authentic OEM metering diaphragm assembly is housed within the carburetor of your lawn and garden equipment. Positioned between the carburetor body and the fuel pump, it regulates fuel delivery and maintains the air-fuel ratio within the engine. It has a self-adjusting vacuum system and responds to the amount of fuel being drawn into...Read more the engine. When the engine runs at higher speeds, more fuel is pulled in and the diaphragm compresses. As a result, the pin in the center of the diaphragm pushes against the metering level and lifts the regulator inlet needle, letting additional fuel flow from the pump into the reservoir. If the assembly malfunctions, you may experience engine stalling, rough idling, or notice fuel odor, pooling, or dripping around the carburetor area. To remove the metering diaphragm, refer to your user guide for instructions on locating and accessing the carburetor. This typically involves removing the fuel pump cover screw and pump cover, followed by the fuel pump diaphragm and gasket. Remember to blow through the external pulse hole on the body casting and remove the filter screen before proceeding to remove the four screws securing the metering diaphragm plate and the metering diaphragm itself. Please note that this replacement part is sold individually.
This is a genuine OEM part. The Husqvarna gasket is constructed of a cardboard composite, and is compatible with many lawn and garden devices. This part is fitted onto the carburetor assembly. This item has been designed to prevent damage to engine parts and absorb fuel leakage. A screwdriver and a wrench may be needed to make the removal...Read more and replacement. This part is sold individually. It is recommended to refer to engine manual and diagrams for further instruction.
This is a genuine OEM part from Husqvarna. The intake sleeve is made of durable plastic, and is compatible with many chainsaw models. This component is designed to secure the air filter onto the chainsaw carburetor. The intake sleeve is sold individually. For the installation, you will need a screwdriver, hex key and a wrench.
This is an OEM part sourced directly from the manufacturer. The air filter is commonly found in Husqvarna brushcutters. This part is made of foam, and is used to remove dust and debris from the air for use in the carburetor. You may require an Allen wrench or hex key when replacing this part. This item is available as an individual replacement part.