3901 - Overview

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individ...Read moreually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

This #191938-1 (CB-408) Makita carbon brush set contains two individual carbon brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes are often the cause...Read more of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

This authentic replacement part which is specially designed for use with Makita power tools. Ball bearings are used to reduce friction between rotating parts, over time components may begin to wear out and fail eventually requiring a replacement. Please note this high-quality ball bearing is made of durable metal and it is sold individually.

This cord guard is a genuine Makita replacement part, and it is a direct replacement for a damaged or missing cord guard. Power tool cords undergo a lot of stress, and these cord guards help to alleviate some of that stress at the weakest point--right where the cord enters the tool. Over time cord guards will deteriorate and eventually re...Read morequire replacement. Keeping a strong cord guard on your tool will help will cord life. This cord guard is compatible with the tools listed below, but it is not guaranteed to fit any other power tools.

This is a genuine Makita replacement part, it is sold individually. It is part of the bit holder. Without this Ball the bit would not stay in the holder. It is used in a number of different tools for different reasons. But it is most popular in Cordless Impact Drivers and Corded Screw Drivers. Compatible with the tools listed below. The diameter is 3.5mm.

This manufacturer sourced replacement pin is made out rubber and it is sold individually. It acts as a cushion/spacer in a variety of Makita power tools. This is a standard piece of hardware and it has multiple applications based on your tool. Please refer to diagrams for correct application.

This genuine manufacturer-sourced part is specially designed for Makita power tools. It is an important component which provides a tight seal between connected components. Unfortunately, over time it will wear out and it may begin to crack eventually requiring a replacement. To ensure the correct repair procedure, refer to the appropriate...Read more diagrams for your model. Note, this high-quality insulation washer is made of durable material and is sold as an individual item. A screwdriver will be needed to take apart and reassemble the tool when performing this repair.

This is a genuine OEM sourced part used on a variety of power tools. The ball bearing 627LLB is often used to help the armature function smoothly. This metal component is sold individually. A wrench, pliers and a screwdriver are helpful with the removal and replacement.

This is an original replacement part sourced directly from the manufacturer. The dust nozzle is found in Makita plate joiners. This part is made of high-quality plastic, and is connected to the base to direct dust away from the work surface. No tools are required when replacing this item. Simply unscrew the old part and thread the new one into place. The dust nozzle is sold as an individual replacement part.

This is a genuine replacement part for various Makita machines. The screw is used to fasten the rear cover to the tool housing. This part is made of high=quality metal. You will need a Phillips head screwdriver to remove this component. This item is sold individually.