EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

38H-3T Maytag Range - Overview

Diagrams for 38H-3T

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Long Oven Sensor – Part Number: 12001656
$43.18
In Stock
Long Oven Sensor
★★★★★
★★★★★
(38)
Part #12001656
This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the internal temperature of your oven cavity. There is an adapter at one end, a probe at the other, and they are connected by an insulated wire. The probe is approximately 7 inches long. You can test the sensor with a multi-meter for functionality. You need to check the model-specific manual to determine what the proper resistance is for your specific appliance. This oven sensor comes with two wire harness adapters and a set of instructions.
Range Terminal Block – Part Number: WPW10245259
$27.36
In Stock
Range Terminal Block
★★★★★
★★★★★
(20)
Part #WPW10245259
This part is for oven ranges, it connects individual wires and protects the device from electrical surges, voltages, and current. With this part, the house power is connected to the range wire harness. Some symptoms replacing the terminal block could be a solution for are little to no heat when baking, element will not heat and/or it will not start. This part will prevent loosening and will reduce damage caused by corrosion (by two different metals). Refer to the instructional diagram for further replacement guidance and exact placement. You must unplug the appliance before installing this part and wear gloves to protect your hands.
Oven Door Spring – Part Number: WP7803P058-60
$15.00
In Stock
Oven Door Spring
★★★★★
★★★★★
(4)
Part #WP7803P058-60
The oven door springs create tension which allows the door to open and close with ease. This spring can be used on either the left or right side of your oven, is made completely of metal, and is approximately 6 inches long. If your oven door will not open or close easily, you may need to replace this part. It may be a good idea to replace both hinges at the same time, because if a spring has become loose, the other hinge is likely to have the same issue. You may need to remove the side panel of the oven to reach where the spring attaches, so make sure the oven is off and is cool to the touch. This part is sold individually.
Bake Element (15 Inch long x 19 Inch wide) – Part Number: WPY04000041
$79.80
In Stock
Bake Element (15 Inch long x 19 Inch wide)
★★★★★
★★★★★
(7)
Part #WPY04000041
This spade style bake element with push on wire terminals is 15 inches long and 19 inches wide. The depth of the terminals is three inches.
Oven Door Gasket – Part Number: 7201P036-60
No Longer Available
Hinge - Left Side – Part Number: 3418A029-34
No Longer Available
Hinge - Left Side
Part #3418A029-34
The hinges allow the door to swing up and down. The hinges must be properly adjusted in order for the door to close properly.
Hinge - Right Side – Part Number: 3418A030-34
No Longer Available
Hinge - Right Side
Part #3418A030-34
The hinges allow the door to swing up and down. The hinges must be properly adjusted in order for the door to close properly.
Electronic Relay Board – Part Number: WP7428P005-60
No Longer Available
Electronic Relay Board
Part #WP7428P005-60
This board sends information (such as temperature of oven, bake, broil) to the main control board during specific functions.
Broil Element Kit – Part Number: WPY04000042
No Longer Available
Broil Element Kit
Part #WPY04000042
This broil element is a little over seventeen inches long, and is not quite thirteen inches wide. It has screw on terminals and a terminal depth of just over three inches. The terminals are just two inches apart. This broil element comes with two screws and an instructions sheet.
Power Cord – Part Number: PT220
$26.82
In Stock
Power Cord
Part #PT220
DISCONTINUED – Part Number: 7902P275-60
No Longer Available
DISCONTINUED
Part #7902P275-60
Power Cord – Part Number: PT500
$35.80
Special Order
Power Cord
Part #PT500

Common Symptoms of the 38H-3T

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven not holding 350 F, when cooling the coils did not reheat
162 of 213 people found this instruction helpful.
  • David from Westford, MA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Was this helpful?
Thank you for voting!
F1-1 code
79 of 110 people found this instruction helpful.
  • charles from marstons mills, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Fa ilure to do so will cause the plastic plug connector to melt from oven heat.
Was this helpful?
Thank you for voting!
Burned terminal block and filter board
95 of 208 people found this instruction helpful.
  • Joseph from Decatur, GA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set, Wrench set
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.
Was this helpful?
Thank you for voting!