389447-0119-01 Briggs and Stratton Engine - Overview

Hard starting or an engine that suddenly stops may point to a damaged magneto armature. This ignition coil turns magnetic energy from the spinning flywheel into the electrical pulse that fires the spark plug. First try a known-good spark plug and inspect the safety switches, grounding wire, terminals, and flywheel magnet. Confirm fit from...Read more the full engine identification numbers, since similar coils may mount differently. Work only with the engine off and cool. Disconnect the battery and spark plug lead before removing covers. During installation, use the air gap listed in the service manual and tighten the mounting screws evenly. Keep hands clear of the flywheel and use an insulated tester to check for spark.

A starter solenoid, also known as a starter relay, is an electrical component that is used within small engine systems to control the starter motor by engaging it when an ignition key is turned - acting as a bridge between the battery and starter motor. This starter solenoid is designed for use with various models of lawn mower and other ...Read moresmall engine equipment and is sold as an individual part with no securing hardware. Depending on your model and type of equipment, the location of the starter solenoid may be different, but it is typically located on or around the engine block, and close to the battery. If you notice issues with starting your equipment such as clicking sounds, intermittent starting or simply not starting at all, the solenoid may be burnt or damaged and need replacement immediately. You can test the solenoid for continuity on its terminals with a multimeter, but make sure to take safety precautions. To replace a starter solenoid, you need only disconnect the equipment from power, locate the solenoid, disconnect and remove any connections and securing bolts before you can replace it and test for full functionality.

This is an authentic Briggs & Stratton replacement part sourced from the original manufacturer for use with small engines. The special screw includes a washer and is commonly used to secure the engine's exhaust manifold. The screw is available as an individual replacement part.

It is an authentic OEM supplied part that is designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. This part provides a seal for the tappet valve. It is an identical replacement for a missing or a faulty part that was included with a new unit. Please make sure to check the appropriate diagrams ...Read moreof your model for exact location and application of this component. Keep in mind this high-quality valve seal is sold individually.

This replacement push-rod is a genuine manufacturer supplied item that is specially designed for Briggs and Stratton engines. The push rod rides on the camshaft to push the exhaust valve open during the exhaust stroke. A bent push rod can seriously affect your engine's performance and it damage the engine if the problem is not taken care ...Read moreof immediately. This part is made out from durable aluminum and it is sold individually.

This is an original part from Briggs & Stratton. The rocket cover gasket is compatible with many small engines. The cardboard composite gasket is designed to prevent damage to engine parts and absorb fuel leakage. A screwdriver and a wrench may be needed to make the removal and replacement. This part is sold individually. It is recommended to refer to engine manual and diagrams for further instruction.

This is a manufacturer approved replacement part used on a variety of lawn and garden equipment engines. This filter adds a second layer of protection against airborne-dirt particle ingestion. This is a foam pre-cleaner which is sold individually. Please note a paper filter and a cover are both sold separately. No tools are needed to rep...Read morelace this filter. • Remove the filter cover • Take out the old filter and replace it with a new one • Secure the top cover

This is an authentic manufacturer-sourced replacement part which is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is an identical replacement for a missing or damaged seal that was originally installed on a new unit, please make sure to check the appropriate diagrams of you...Read morer model for the correct location and application of this hardware. Keep in mind this high-quality item is made of durable rubber and is sold individually.

This replacement oil filter is a genuine OEM sourced item commonly utilized on Briggs and Stratton engines that are commonly installed on lawn and garden equipment. This filter helps to remove harmful contaminants from engine oil that is needed for operation. This part is manufactured in accordance with applicable EPA emissions regulation...Read mores to maintain optimum engine performance. It is recommended to replace it at least once a season. Please note this oil filter is sold individually requiring a wrench to secure or remove it.

This is a genuine manufacturer-approved replacement part which is specially designed for use on Briggs and Stratton engines commonly installed on lawn and garden equipment. The push rod rides on the camshaft to push the exhaust valve open during the exhaust stroke. A bent rod can not only affect your engine's performance, it can seriously...Read more damage other parts if the problem is not taken care of immediately. Keep in mind this high-quality part is made of durable metal and is sold individually.

This is a genuine replacement part manufactured for use with small engines. The spark plug is used to fire the air-fuel mixture inside the cylinder. This spark plug is available as an individual replacement part, please see model diagram for associative parts.

This flywheel puller is designed for servicing larger small engines by safely removing tightly seated flywheels without stressing the crankshaft or damaging ignition components. Constructed from heavy-duty steel and engineered to apply even pulling force, it makes accessing the magneto, crankshaft key, or ignition system straightforward d...Read moreuring repairs or overhauls. Built to OEM specifications for durability and precise fit, it’s a reliable tool for maintaining lawn mowers, generators, and pressure washers with compatible engines.