This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges.
Customers found this to be an easy repair.
This blade is sourced directly from the manufacturer for use in Craftsman and Husqvarna lawn mowers. The blade is the part of the mower that is responsible for cutting and mulching the grass. It is 22" long, made of black metal, is not part of a kit or assembly, and is sold individually.
If you hit a hard object, you may bend the blade,...Read more causing a vibration. You may also have problems with the grass being cut as the blade dulls over time. If the blade is bent, damaged, or worn, it needs to be replaced. You will need a socket set to complete this repair.
Customers rate this repair as Easy.
The Dust Shield is a 6-3/4 inch, black plastic part, used to prevent dust or debris fouling the wheel or axle. It attaches inside of the wheel around the axle. Installation is rated as "Easy" and will require a wrench. If broken, damaged, or worn due to fatigue, you will see visable damage and you may have debris getting caught in the axl...Read moree. If broken, replace it. Refer to your make, model and diagram to make sure you're choosing the right part. This part comes individually sold.
This Genuine OEM blade control cable assembly is designed for use with walk-behind and push lawn mowers. Sold individually, it includes a durable metal wire cable with Z-type bent ends, a rubberized protective cover, and a plastic mounting clip. This essential component connects the control handle to the engine brake system, stopping the ...Read moreblade when the handle is released to ensure safe operation.
If the cable is broken, the brake may remain engaged even when the lever is pressed. Replacing the cable is a straightforward process that may require a pair of pliers. Begin by identifying where the old cable is attached to the motor assembly and remove it. Install the new cable in the same location, then route it up to the control handle. Insert the Z-shaped end into the hole in the control handle, just as with the original cable. Once both ends are connected, remove the upper mount of the old cable from the handle and secure the new one in its place. Finally, tie the cable in the same manner as the original, ensuring there is enough clearance and free play to prevent over-bending or premature wear. This replacement restores proper blade control and helps maintain safe mower operation.
This genuine manufacturer sourced replacement part is designed for use with lawn mowers.It attached to the mower deck to protect your feet and legs from grass clippings and debris. It is made out of plastic and it is sold individually. Please note the brackets and hardware are sold separately.
This is an authentic OEM self-tapping bolt used on Toro snow throwers/blowers. It is designed to secure the bushing/gear case assembly together. By using a wrench and a self tapping bolt, precisely fitted threads are created in the opening of the case. This allows for the two part to be secured tightly together. Please note this bolt is sold individually.
A washer is used for things such as load distribution, stability, alignment and protection for whatever equipment it is fastened between. This curved washer, also known as a wave washer or spring washer, is made of metal and features a curved design that allows for applications in settings where objects being fastened together are also cu...Read morerved or to exert a continuous level of tension. This washer measures approximately 1-inch in outer diameter and 1/3-inch inner-diameter and is compatible with and used on equipment like snowblowers, chainsaws and lawnmowers. This washer is installed between a round fastener or knob to better secure them together and if you notice that where the washer is normally connected is loose or vibrates excessively, this washer likely needs replacing. Depending on your model the replacement process may appear different, but it is just as simple as placing the washer between two things that are connected and securing them tightly.
This snap ring fits into a groove to hold a pinion gear or other drive part in place. A loose drive part may mean the ring is bent, weak, or missing. Check the groove, washers, bearings, and shaft for damage before replacing it. Confirm fit with the full machine model, serial range, and parts diagram. Turn off the equipment and disconnect...Read more the battery or spark plug lead when needed. Wear eye protection and use retaining-ring pliers. Make sure the new ring sits fully and evenly in the groove before use.
This screw is an OEM part sourced directly from the manufacturer and is used in Toro snowthrowers. It requires a wrench and connects the ring-chute to the chute-discharge. The screw is made of metal and is sold as an individual part. Screws will need to be replaced when they become stripped.
It is a genuine OEM supplied item which is made for walk-behind lawn mowers. This is a high-quality replacement for a missing or a damaged pinion gear that helps to drive the mower's wheel. Unfortunately, over time due to friction, the teeth on the gear may wear out. If this happens it will no longer engage the wheel and the mower will no...Read moret move. To ensure the exact location and the correct installation of the new part, refer to the diagrams of your specific model. Note, one durable metal pinion is included. You will need a wrench set and pliers to remove the old pinion and secure the new one.
Made of high-quality metal, this hex flange locknut is designed for use with various lawn mowers and ride-on mower/tractor models and is sold individually. This locknut attaches to the end of the carriage bolt and is an important component to the axle assembly. This locknut has a 3/8-inch inner-diameter and is 16 threads-per-inch. To repl...Read moreace this locknut, you will need a wrench, and if there are multiple locknuts on your equipment, they may all need to be replaced.
The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced.
Customers found this to be an easy repair.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Cable was broke.
6 of 7 peoplefound this instruction helpful.
James from ASHTABULA, OH
Really Easy
15 - 30 mins
Pliers
Pushed the cable through the engine mount.Connected the cable to the engine slider. Pulled cable through the previous tie down connected to the lower end of the bar. Attached the connector on the cable to the hole in the lawn mower bar near the top of the bar.. Attached the top end of the cable to the on/off bar where you push the mower.
Was this helpful?
Thank you for voting!
Drive cable broken
5 of 6 peoplefound this instruction helpful.
Frank from AUSTIN, TX
Very Easy
Less than 15 mins
Nutdriver, Pliers
Remove the front drive cover and disconnect the old from the drive, hook the new drive cable to the drive, and connect new cable back to the handle. Reinstalled the drive cover, started unit, and test that the drive was working correctly.
Was this helpful?
Thank you for voting!
Front drive wheel locked up, causing the mower to not be able to be pushed.
4 of 12 peoplefound this instruction helpful.
Walter from EVERETT, WA
Easy
Less than 15 mins
Socket set
Removed wheel by pressing off the plastic hub cap exposing the nut holding the wheel. I removed the nut, then pulled the wheel straight off the axel shaft. This exposed the broken dust cover. I they wiggled the dust cover off, cleaned the dirt from inside the wheel, placed the new dust cover, replaced the wheel, nut and hub cap.