This evaporator fan motor grommet, or condenser fan grommet is built for refrigerators. It provides a cushion between the fan motor and the motor mounting bracket. It is made or round, black plastic a...
The interior light of your refrigerator is controlled by a switch that is activated when the door is opened and closed. If your refrigerator light will not turn on, there could be an issue with the sw...
This compression ring is meant to hold the evaporator fan motor in place in the freezer compartment of your refrigerator. This is is a genuine OEM part. The tools needed to complete this repair are a ...
This 40-Watt light bulb is sold individually and is a genuine OEM replacement option for your home appliances. It is specially designed to withstand extreme temperatures, so this bulb is compatible wi...
This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. This part has been updated by the manufacturer and may appear different t...
The condenser fan blade assembly helps to regulate the temperature in your refrigerator or freezer. This fan assembly has 4 blades, but other fans may have 3 blades, so be sure to check the number of ...
This is the replacement hinge washer for your refrigerator. The hinge washer is mounted on the top of the door hinge pin, and supports the refrigerator door, allowing it to open and close easily. The ...
This refrigerator door handle mounting screw connects your refrigerator door to the handle. The part is less than 1 inch in length, and can come in both silver and gold colors. When installing this sc...
This is the replacement vegetable pan cover for your refrigerator. It is made of white plastic and measures approximately 26 inches by 18 inches. This part is the frame of the pan only, and does not i...
I applied some tips learned by reading other reviews. So before I started I grabbed my trusty vise grip pliers and a small screw driver. I locked onto the switch actuator, the part that the refrigerator door pushes in, with the vise grips and pulled on it just hard enough to get the screw driver inserted in the right side to push in the c
... Read moreatch clip so the switch could be pulled out further each time the catch clip was depressed to the next detent. Then I used the screw driver on the left site to encourage the switch past the detents on the left and very quickly the switch was out of the mount. The wires from the refrigerator pulled out with the old switch. I unplugged the old switch from the wires and plugged in the new switch and shoved the new switch back into the mount, wiggled it a couple of times to make sure it was secure and the job was done. Once I applied the vise gripes at first, the whole job took less than a minute.
Could not haven been easier. Simply unplug fridge, remove air duct mounted on rear panel, release panel itself, pull fan blade off, disconnect grounding wire, detach fan motor bracket, disconnect wire harness to release fan motor, install new fan motor and reconnect, secure with bracket, reconnect grounding wire, reposition fan blade onto
... Read more motor shaft, reinstall rear panel and secure screws. Remount air duct and plug appliance back in. VOILA. All done in less than 15 minutes!!!
The Fridge and freezer were not very cold except for in the very back of the freezer (where the coils are). So I opened up the back of the freezer by first removing the dome light cover and removing all the visible screws. I then lifted up and pulled out the vent in the center of the back panel and removed the two remaining screws on the
... Read moreback panel. At that point I removed the back panel exposing the coils and fan. I saw that the fan was not spinning so I used a screw driver to manually turn the defrost timer found on the top of the inside of the fridge. Once I had turned the defrost timer once complete rotation, and the fan didn't turn on, I was pretty sure that it was the fan. I still wasn't sure that the fan was the only problem, but I couldnt see anything else that wasn't working properly. I decided to take a chance and order the fan motor (not the entire assembly. it is easy to replace the moter only leaving the original fan blades and housing). Once I got the part, I unplugged the old fan motor, put in the new fan motor, and pugged it in and it started spinning right away. I put everything back together the same way I took it apart and it has worked great ever since.
