This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges.
Customers found this to be an easy repair.
A washer is used for things such as load distribution, stability, alignment and protection for whatever equipment it is fastened between. This curved washer, also known as a wave washer or spring washer, is made of metal and features a curved design that allows for applications in settings where objects being fastened together are also cu...Read morerved or to exert a continuous level of tension. This washer measures approximately 1-inch in outer diameter and 1/3-inch inner-diameter and is compatible with and used on equipment like snowblowers, chainsaws and lawnmowers. This washer is installed between a round fastener or knob to better secure them together and if you notice that where the washer is normally connected is loose or vibrates excessively, this washer likely needs replacing. Depending on your model the replacement process may appear different, but it is just as simple as placing the washer between two things that are connected and securing them tightly.
This is a genuine Toro replacement part that has been sourced from the original manufacturer to be used with snowthrowers. The metal hex head screw is used to secure the impeller assembly. This item is available as an individual replacement part.
This OEM Carburetor Bowl Gasket attaches between the carburetor bowl and carburetor in order to seal the parts together. This model is rubber, black, and comes individually sold. Installation is rated as "Easy" by customers, and will require pliers and a socket set. If the part becomes broken due to wear/damage then there may be a fuel le...Read moreak, and the part will need to be replaced. Refer to your make, model and diagrams to ensure you've chosen the correct part.
This snap ring fits into a groove to hold a pinion gear or other drive part in place. A loose drive part may mean the ring is bent, weak, or missing. Check the groove, washers, bearings, and shaft for damage before replacing it. Confirm fit with the full machine model, serial range, and parts diagram. Turn off the equipment and disconnect...Read more the battery or spark plug lead when needed. Wear eye protection and use retaining-ring pliers. Make sure the new ring sits fully and evenly in the groove before use.
This screw is an OEM part sourced directly from the manufacturer and is used in Toro snowthrowers. It requires a wrench and connects the ring-chute to the chute-discharge. The screw is made of metal and is sold as an individual part. Screws will need to be replaced when they become stripped.
The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced.
Customers found this to be an easy repair.
A loose or tilted mower deck may be caused by a damaged hanger bracket. This replacement bracket mounts at the right rear of the deck and helps hold it at the proper height. It also gives the deck a pivot point for raising and lowering. Replacing a cracked, bent, or worn bracket can help the deck sit evenly during use. Turn off the machin...Read moree, disconnect its power source, and support the deck before removing any hardware. Check the owners manual for the correct fastener positions and tightening steps.
The Fuel Line Clamp is a metal, individually sold part which clamps onto the fuel line, securing it to a port and preventing leaks. Installation is rated as "Easy" by customers and will require pliers and a screwdriver. If broken due to wear/fatigue/damage, there may be a fuel leak and the part should be replaced. Refer to your make, model and diagrams to ensure this is the correct part.
This is an OEM sourced replacement part used with a variety of lawn and garden equipment. A spark plug delivers electric current from an ignition system to an internal combustion engine. After time spark plugs will become dirty or fouled. It is a good idea to replace the spark plug once this happens. This item is sold individually. You s...Read morehould gap your spark plug according to the owners manual of the outdoor product you have. You would need a spark plug wrench or a socket wrench to install the spark plug.