This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges.
Customers found this to be an easy repair.
The fuel tank goes between the fuel tank bracket and the fuel line. This is a Tecumseh, Husqvarna, and Toro replacement part directly sourced from the manufacturer for use in engines and snowthrowers. This part holds the fuel and is priced individually. A wrench might be required during the replacement of this part. It will need to be replaced if it leaks.
This is an authentic OEM sourced replacement part, it is specially made for use with lawn and garden equipment. It is a standard hardware which has multiple applications depending on your model, please refer to appropriate diagrams for correct location and use of this item. Please note this high-quality hex head screw is sold individually.
This is an authentic OEM self-tapping bolt used on Toro snow throwers/blowers. It is designed to secure the bushing/gear case assembly together. By using a wrench and a self tapping bolt, precisely fitted threads are created in the opening of the case. This allows for the two part to be secured tightly together. Please note this bolt is sold individually.
This OEM Carburetor Bowl Gasket attaches between the carburetor bowl and carburetor in order to seal the parts together. This model is rubber, black, and comes individually sold. Installation is rated as "Easy" by customers, and will require pliers and a socket set. If the part becomes broken due to wear/damage then there may be a fuel le...Read moreak, and the part will need to be replaced. Refer to your make, model and diagrams to ensure you've chosen the correct part.
This snap ring fits into a groove to hold a pinion gear or other drive part in place. A loose drive part may mean the ring is bent, weak, or missing. Check the groove, washers, bearings, and shaft for damage before replacing it. Confirm fit with the full machine model, serial range, and parts diagram. Turn off the equipment and disconnect...Read more the battery or spark plug lead when needed. Wear eye protection and use retaining-ring pliers. Make sure the new ring sits fully and evenly in the groove before use.
This screw is an OEM part sourced directly from the manufacturer and is used in Toro snowthrowers. It requires a wrench and connects the ring-chute to the chute-discharge. The screw is made of metal and is sold as an individual part. Screws will need to be replaced when they become stripped.
The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced.
Customers found this to be an easy repair.
This is a Manufacturer Approved replacement nut for lawn and garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt.
The Fuel Line Clamp is a metal, individually sold part which clamps onto the fuel line, securing it to a port and preventing leaks. Installation is rated as "Easy" by customers and will require pliers and a screwdriver. If broken due to wear/fatigue/damage, there may be a fuel leak and the part should be replaced. Refer to your make, model and diagrams to ensure this is the correct part.
This is an OEM sourced replacement part used with a variety of lawn and garden equipment. A spark plug delivers electric current from an ignition system to an internal combustion engine. After time spark plugs will become dirty or fouled. It is a good idea to replace the spark plug once this happens. This item is sold individually. You s...Read morehould gap your spark plug according to the owners manual of the outdoor product you have. You would need a spark plug wrench or a socket wrench to install the spark plug.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bad Camshaft made of plastic
5 of 9 peoplefound this instruction helpful.
Dan from Millstone Twp, NJ
Really Easy
30 - 60 mins
Ordered a replacement camshaft and had a terrible result. Supposed to be in stock but wasn't. NO update on when the part would arrive. NO contact unless I initiated it. Only email I received stated NO information on when part would arrive. I asked for Customer service to reach out for more details and they balked, did not want to do a
... Read morenything. I insisted and the result was an email stating no idea. No further info from anyone. I figured my next step was to ask for a refund but figured it would not be refunded. I then found a "dead" engine and used THAT camshaft for my repair. Weeks later your part arrived with ZERO notice. I should have asked for a refund due to your failure to live up to your hype. ZERO stars for this junk. Will NOT ever use you again.