This manufacturer-certified Primer Bulb is a black rubber part which comes individually sold. It is used to pump fuel from the fuel tank to the carburetor to start the engine. Installation is rated as "Easy" by customers, and will require a screwdriver and pliers. The part attaches to the primer assembly. If the bulb breaks due to wear/fa...Read moretigue/damage you will see fuel leaking, and the part should be replaced. Refer to your make, model and diagrams to ensure this is the correct part.
A washer is used for things such as load distribution, stability, alignment and protection for whatever equipment it is fastened between. This curved washer, also known as a wave washer or spring washer, is made of metal and features a curved design that allows for applications in settings where objects being fastened together are also cu...Read morerved or to exert a continuous level of tension. This washer measures approximately 1-inch in outer diameter and 1/3-inch inner-diameter and is compatible with and used on equipment like snowblowers, chainsaws and lawnmowers. This washer is installed between a round fastener or knob to better secure them together and if you notice that where the washer is normally connected is loose or vibrates excessively, this washer likely needs replacing. Depending on your model the replacement process may appear different, but it is just as simple as placing the washer between two things that are connected and securing them tightly.
This OEM Carburetor Bowl Gasket attaches between the carburetor bowl and carburetor in order to seal the parts together. This model is rubber, black, and comes individually sold. Installation is rated as "Easy" by customers, and will require pliers and a socket set. If the part becomes broken due to wear/damage then there may be a fuel le...Read moreak, and the part will need to be replaced. Refer to your make, model and diagrams to ensure you've chosen the correct part.
This screw is an OEM part sourced directly from the manufacturer and is used in Toro snowthrowers. It requires a wrench and connects the ring-chute to the chute-discharge. The screw is made of metal and is sold as an individual part. Screws will need to be replaced when they become stripped.
The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced.
Customers found this to be an easy repair.
This ignition key is used in lawn equipment to start and stop its engine. Inserting the key into the ignition switch activates the starter motor. Thus, it is a safety device which prevents accidental or unauthorized use of the equipment. A broken key might be loose or hard to turn. In some cases, it might have completely fallen out of the...Read more switch. Without the ignition key, it will be difficult or impossible to start the engine. Locate your ignition key by reading your user manual. To remove a stuck ignition key, you may need to use a small amount of lubricant on it. While turning the key in the ignition switch, gently wriggle it back and forth. There may also be a release button that you could press, depending on your model type. This replacement part is an OEM product and is sold per unit.
This is an authentic manufacturer sourced replacement part designed for use with Toro snow throwers/blowers. This part helps to secure the primer bulb and connect the fuel hose. It is made out of plastic and it is sold individually.
This is a Manufacturer Approved replacement nut for lawn and garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt.
The Fuel Line Clamp is a metal, individually sold part which clamps onto the fuel line, securing it to a port and preventing leaks. Installation is rated as "Easy" by customers and will require pliers and a screwdriver. If broken due to wear/fatigue/damage, there may be a fuel leak and the part should be replaced. Refer to your make, model and diagrams to ensure this is the correct part.
This metal ball bearing reduces friction and evenly distributes weight among the rotating parts in your lawn equipment. These bearings can be found in various areas such as the wheels, in pulleys, blades or augers. When the bearing is damaged, you may notice a few things. Your machine may produce rough or grinding noises and excessively p...Read morelay or wobble. The affected part may also become stuck. Immediate replacement is necessary to prevent increased friction, inefficient performance, and potential equipment failure. Removing the bearing depends on your model, so consult your user manual for guidance. You will need to use a screwdriver or pliers to remove the surrounding components around the bearing and a bearing puller, pry bar, or mallet to release the bearing itself from its housing. As ball bearings wear out together, it is advisable to replace all of them at once. Ensure you verify the number of bearings your machine needs before purchasing this OEM replacement part as it is sold individually.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Grandson lost the ignition key to my Toro!
15 of 38 peoplefound this instruction helpful.
Michelle from AYLETT, VA
Really Easy
Less than 15 mins
No repair, lol! Just a perfect fit for my ignition :). I bought two in case my grandson gets curious again.
Was this helpful?
Thank you for voting!
Bad Camshaft made of plastic
5 of 9 peoplefound this instruction helpful.
Dan from Millstone Twp, NJ
Really Easy
30 - 60 mins
Ordered a replacement camshaft and had a terrible result. Supposed to be in stock but wasn't. NO update on when the part would arrive. NO contact unless I initiated it. Only email I received stated NO information on when part would arrive. I asked for Customer service to reach out for more details and they balked, did not want to do a
... Read morenything. I insisted and the result was an email stating no idea. No further info from anyone. I figured my next step was to ask for a refund but figured it would not be refunded. I then found a "dead" engine and used THAT camshaft for my repair. Weeks later your part arrived with ZERO notice. I should have asked for a refund due to your failure to live up to your hype. ZERO stars for this junk. Will NOT ever use you again.
Read less
Was this helpful?
Thank you for voting!
Bad Camshaft made of plastic
2 of 2 peoplefound this instruction helpful.
Dan from MILLSTONE TWP, NJ
Very Difficult
More than 2 hours
Original engine had camshaft made of plastic. Engine had a seal leak on shaft lost oil . Result was seized bearing and stripped camshaft. Ordered a replacement camshaft and gasket. Gasket came in a week after original due date and camshaft is NOT AVAILABLE. Didn't know that at original order. Followed up twice with operator, not ema
... Read moreil and got a non-answer answer. No idea when part will be available and requested a second contact and update. Same no idea reply. Result is a waste of my time with this company, will NOT use them again.