38518X58B Murray Lawn Tractor - Overview

This is a genuine Murray replacement part, it is sold individually. It is commonly used in lawn tractors, and is used in various places in the compatible models listed below. It is self tapping, with a 9/16 hex head. Made of metal.

This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in length. Your machine may have a loud hissing or popping sound coming from the exhaust area if the gasket was faulty. You may also notice th...Read moree presence of black soot around the gasket or the exhaust. Your gasket needs to be replaced if it appears worn or deformed. Otherwise, your machine will experience exhaust leaks. To detach the gasket, remove the fasteners that secure it using a socket or wrench. You can detach the gasket from your machine afterwards. Please bear in mind that this replacement part is sold individually.

The Blade Adapter is used to connect the mower blade to the base of the mower deck. The part is individually sold, silver metal, and measures approximately 2 inches in diameter. Installation requires a Wrench or Socket and is rated as "Easy". If damaged (likely due to fatigue and general wear) there maay be a vibration or rattling sound f...Read morerom it coming loose. Refer to your make, model and diagrams to ensure this is the correct part.

This 1/4-inch?20 UNC hex-head screw is 1 inch long. It secures a part on select small gasoline engines, but its exact location can change by model. Use the full engine model, type, and code numbers to guarantee the proper fit and placement. Turn off the engine, let it cool, and disconnect the spark plug before service. Check the mounting ...Read morehole and nearby parts for damage. Tighten the screw to the setting listed in the engine manual.

This hex nut is a fastener made from steel and is used to secure the end of a bolt in various lawn and garden equipment and machinery. It is a genuine OEM replacement part that comes in a standard size of 5/16 of an inch with 18 threads per inch. The hex nut has a hexagonal shape, which gives it greater grip and makes it easy to tighten u...Read moresing a wrench or a set of pliers. The nut also has a flange on one end, which locks the nut in place, prevents damage to the area where it is installed, and allows the load to be evenly distributed. It is important to replace your hex nut if it is loose, cracked, or corroded. If you have not yet removed the old hex nut from your equipment you will need a socket wrench to remove it. After that, you can easily install the new nut by threading it onto a bolt or screw and then tightening it with a wrench or pliers until it is tightly secured.

The hair pin is a silver, metal pin used to secure and lock parts in place. If broken, the part being secured will come loose and the pin should be replaced. This is an OEM part directly from the manufacturer. Most customers rated the replacement of the hair pin as an easy repair.

The Blade Nut is a 9/16-18" silver, metal nut. This part is sold individually, and requires a wrench and socket to install. Its installation is rated "Easy". This part secures the blade in place and attaches onto the blade shaft. If broken (likely due to fatigue) it may come loose and rattle, causing vibrations. Refer to your make, model and diagrams to ensure this is the correct part.

This replacement switch is a genuine OEM part, not an aftermarket equivalent. It is supplied directly from original equipment manufacturer for Murray riding lawn mowers and tractors. This switch is secured under the seat to prevent the engine from running without a driver in a seat. Mechanical switches over time tend to wear out requiring replacement. Please note, this plastic switch is sold individually.

This centerlock nut, or lock nut, is sold individually and locks itself in place when inserted, to prevent it from backing out due to vibration. Over time, due to its strenueous job, it may become loose or break due to wear and tear, and will need to be replaced. This lock nut is made of metal and is silver in color. When it will no longe...Read morer lock, you will need to complete this easy repair, which requires a wrench or socket and torque wrench. Ensure you torque the lock nut to your manufacturer specifications; this nut can have a range of different applications for a variety of equipment, so please check your model number or owners manual to be sure it is the right fit for your model.

This is a metal star screw. It is a genuine OEM sourced part which is specifically designed for use with Briggs & Stratton engines and generators, and Toro snowthrowers, tillers, blower-vacuums, lawn tractors, and lawn mowers. This is available as an individual replacement part. A Torx screwdriver will be needed to replace this part if it becomes stripped or lost.

This replacement washer is a genuine OEM sourced part. It is commonly used on a variety of Murray riding lawn mowers and tractors. Washers helps to distribute the pressure evenly between two connected parts. This washer is generally used to help securing mower wheels. For proper application please refer to diagrams of your model. This met...Read moreal washer is sold individually. When replacing it you should only need a wrench to remove the lock nut that secures the wheel to the axle.