382 (Type 2) Porter Cable Orbital or Palm Sander - Overview

The 151281-08 Pad is used to hold 5 inch Hook and Loop sandpaper with 8 vacuum holes. Over the past few years the popularity of Hook and Loop paper has grown because of the ease of changing sandpaper when needed. Over that of the PSA (Pressure Sensitive Sandpaper) Applying too much pressure on the sander may cause premature wear on th...Read moree Hook and Loop pad. When a pad needs to be replaced, simply remove the three screws that hold the pad to the sander, then replace it with a new pad.

This is a genuine OEM replacement part, it is sold individually. This part is used to keep the brush tight against the armature so the tool will work properly. Over time when the brushes wear down and heat is created, the spring may lose its tension and will have to be replaced.

Genuine OEM replacement part designed for certain Random Orbit Sanders. This item is made out of Metal and it is Sold Individually. This is the bottom Bearing Retainer that keeps the bearing in place. It is attached to the fan with 3 screws which are Sold Separately.

It is a high-quality OEM part that is specially made for Porter Cable, Black and Decker and DeWALT power tools. The receptacle is designed to safely secure and connect a wire. It is an identical replacement for a faulty or a missing part that was installed on a new unit. To ensure the correct application, refer to the appropriate diagrams...Read more of your model. Note, this high-quality receptacle is made of durable metal and is sold individually. You will need a screwdriver to take the housing apart when replacing this component.

Genuine OEM replacement part, this item is sold individually. The 151553-00 Dust Seal/Brake is a dual propose part. It is a Dust Seal to help prevent dust and debris from entering the motor assembly. It also acts as a Brake to keep the sanding pad at lower RPM so the sander will work properly. It is a good idea to replace this part when you are replacing the sanding pad.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-ring failure. The most common among power tools are: • The O-ring has ragged, tattered edges. These are commonly caused by pressure ...Read morespikes which shear off tiny "bites" from the O-ring, or caused by clearance gaps. • One or both sides of the O-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit, or is too smooth to allow lubrication. • The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding O-ring capacity. • The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays, and air pollution. Excessive seal stretching (greater than 5%) causes similar cracking.

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 18 Gauge • 10 Feet Long

This genuine cord protector, also known as a strain relief boot, is designed to safeguard the power cord where it enters your tool housing. Made from flexible, durable material, it helps prevent the cord from bending, twisting, or fraying during regular use, supporting safe and reliable performance. Small but essential, this component is ...Read morean effective replacement if the original protector is worn or damaged, helping extend the life of your tool and maintain proper cord alignment.

This replacement screw is an authentic OEM sourced item, not an aftermarket equivalent. This is screw is used in a lot of different applications depending on your tool. Please check appropriate diagrams for correct use and location of this screw. This pan head screw is sold individually. You will need a torx screwdriver when working with this hardware.

Genuine OEM replacement part, this item is sold individually. This screw is used in various places in all of the tools listed below The most common use for this screw is to secure plastic housings together. It has a Torx T-20 head.

This item is an authentic, OEM sourced replacement part that is intended to be used with random orbital sanders from DeWalt, Black & Decker, and Porter Cable. The retainer is used to support the bearing between the fan and the sanding pad. This item is available as an individual replacement part.