This is a replacement screw, also known as a shear pin that is used in several pieces of outdoor power equipment. It is made of metal and is approximately 2 inches in length. It is a hex head screw and is sold individually. This is an OEM part sourced directly from the manufacturer.
This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges.
Customers found this to be an easy repair.
This manufacturer-certified Primer Bulb is a black rubber part which comes individually sold. It is used to pump fuel from the fuel tank to the carburetor to start the engine. Installation is rated as "Easy" by customers, and will require a screwdriver and pliers. The part attaches to the primer assembly. If the bulb breaks due to wear/fa...Read moretigue/damage you will see fuel leaking, and the part should be replaced. Refer to your make, model and diagrams to ensure this is the correct part.
This spark plug is designed to provide reliable ignition and efficient fuel combustion in small engine applications. Built for consistent performance and durability, it helps maintain smooth operation, steady power output, and easier starting. Ideal for routine maintenance or replacement, it supports dependable engine performance in lawn and garden equipment, generators, and similar outdoor power machines.
Hard starting or an engine that suddenly stops may point to a damaged magneto armature. This ignition coil turns magnetic energy from the spinning flywheel into the electrical pulse that fires the spark plug. First try a known-good spark plug and inspect the safety switches, grounding wire, terminals, and flywheel magnet. Confirm fit from...Read more the full engine identification numbers, since similar coils may mount differently. Work only with the engine off and cool. Disconnect the battery and spark plug lead before removing covers. During installation, use the air gap listed in the service manual and tighten the mounting screws evenly. Keep hands clear of the flywheel and use an insulated tester to check for spark.
This is an authentic OEM sourced replacement part, it is specially made for use with lawn and garden equipment. It is a standard hardware which has multiple applications depending on your model, please refer to appropriate diagrams for correct location and use of this item. Please note this high-quality hex head screw is sold individually.
A washer is used for things such as load distribution, stability, alignment and protection for whatever equipment it is fastened between. This curved washer, also known as a wave washer or spring washer, is made of metal and features a curved design that allows for applications in settings where objects being fastened together are also cu...Read morerved or to exert a continuous level of tension. This washer measures approximately 1-inch in outer diameter and 1/3-inch inner-diameter and is compatible with and used on equipment like snowblowers, chainsaws and lawnmowers. This washer is installed between a round fastener or knob to better secure them together and if you notice that where the washer is normally connected is loose or vibrates excessively, this washer likely needs replacing. Depending on your model the replacement process may appear different, but it is just as simple as placing the washer between two things that are connected and securing them tightly.
This OEM Carburetor Bowl Gasket attaches between the carburetor bowl and carburetor in order to seal the parts together. This model is rubber, black, and comes individually sold. Installation is rated as "Easy" by customers, and will require pliers and a socket set. If the part becomes broken due to wear/damage then there may be a fuel le...Read moreak, and the part will need to be replaced. Refer to your make, model and diagrams to ensure you've chosen the correct part.
This genuine part is sourced directly from the original equipment manufacturer. It is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The purpose of this hose is to transfer vacuum from the engine. Unfortunately, over time the material may wear out and begin to crack eventually ...Read morerequiring a replacement. Make sure to check the diagrams of your model for the exact location and the correct installation of this part. Note, this item includes one durable rubber hose and two metal clamps to secure it.
The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced.
Customers found this to be an easy repair.
This is an authentic Briggs & Stratton replacement part sourced from the original manufacturer for use with small engines. The special screw includes a washer and is commonly used to secure the engine's exhaust manifold. The screw is available as an individual replacement part.
It is an authentic OEM supplied part that is designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. This part provides a seal for the tappet valve. It is an identical replacement for a missing or a faulty part that was included with a new unit. Please make sure to check the appropriate diagrams ...Read moreof your model for exact location and application of this component. Keep in mind this high-quality valve seal is sold individually.