This is an authentic OEM replacement kit for use with lawn and garden equipment. Each kit includes the carburetor, cylinder, crankcase, and muffler gaskets. The carburetor gasket seals the area between the carburetor and engine block to prevent the entry of contaminants into the carburetor. The crankcase gasket prevents oil from leaking o...Read moreut of the crankcase. The cylinder and muffler gaskets prevent the combustion and exhaust gases from escaping. If you are experiencing common problems such as leaking, loss of compression, and poor engine performance this indicates that your gaskets may be worn down or damaged and need replacement. Carefully remove the old gaskets and thoroughly clean the mating surfaces where the new gaskets will be installed to ensure a good seal. Install the new gaskets and ensure that they fit properly.
The Lever and Knob Assembly (or Front Wheel Height Adjuster) is used to adjust the front height of the mower, and attaches on the front wheels. It can be installed using a socket set and wrench set, and is rated as "easy" to install by our customers. If broken or damaged (likely due to general wear over time) you will no longer be able to...Read more move it to make adjustments, and the part should be replaced. This black, plastic part is sold individually. Refer to your make, model and diagrams to ensure this part fits your machine.
This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with chainsaws. The oil cap connects to the saws chassis by covering the oil fill spout to prevent spills and to prevent contaminants from entering the oil tank. This item is available as an individual replacement part. Tools are not necessary to install this item.
This OEM bar adjustment retainer is a metal component that securely holds the adjustment screw and pin in place, allowing you to adjust the chain tension. It is typically located near the front of the chainsaw, close to the guide bar. If the guide bar is over-pressured, the retainer can become stressed and fail, causing it to ride up on t...Read morehe screw. Signs of a damaged retainer include visible breaks or deformations. You may also have trouble in tightening or loosening the chain, as the screw may become loose during adjustment. To remove a faulty retainer, remove the side cover by loosening the nuts and the tension screw on it with a socket. Unscrew the guide bar and replace the damaged retainer. When installing the new retainer, ensure the cone points towards the adjustment pin. Please note that the replacement retainer is sold separately from the guide bar and adjustment pin.
This is an authentic item sourced from original manufacturer. If the chainsaw bar doesn't adjust when you turn the tension screw usually the tension gear/pin or the adjustment bolt is worn or damaged. This part is made out of metal and it is sold individually. You would need a phillips head screwdriver to remove or secure this screw.
This genuine replacement screw is a high-quality OEM part designed for use with Paramount and Poulan gas-powered lawn and garden equipment. It is specifically engineered to secure the starter rope within the pulley, ensuring reliable starting performance.
Made from durable metal, this specialty screw is sold individually.
Installation...Read more Tip: A flat-head screwdriver is required for removal and installation.
For proper placement and application, please refer to your equipment’s model diagram.
This is a genuine OEM sourced replacement part used with Poulan hedge trimmers. A spark plug delivers electric current from an ignition system to an internal combustion engine. After time spark plugs will become dirty or fouled. It is a good idea to replace the spark plug once this happens. This item is sold individually. You should gap y...Read moreour spark plug according to the owners manual of the outdoor product you have. You would need a spark plug wrench or a socket wrench to install this component.
This bar adjusting pin hooks onto the crankcase along with the bar adjust retainer and the screw. When you tighten the screw it helps to place tension on the bar. This high-quality pin is made out of metal and is sold individually. It is an authentic OEM sourced item which is specially produced for use with Poulan chainsaws. A screwdriver and a socket set may be needed when replacing this part.
This item is sold individually, but keep in mind that two may be needed. The lower isolator fits next to the retainer mount and helps to reduce vibrations. It is made of a hard rubber and will need to be replaced if it breaks. During the replacement process, a screwdriver may be required. This is a Poulan replacement part directly sourced from the manufacturer for gas chainsaws.
This Bell-Wash Flat Washer is an OEM part that measures .40 inches I.D. x 88 inches O.D. This washer is a silver, metal, washer sold individually.
This part is rated as Easy to install by customers. If missing or damaged (likely due to fatigue) it should be replaced. Refer to your owners manual to ensure this is the correct part for you.
This authentic manufacturer-sourced component is specially designed for Poulan and Husqvarna gas-powered chainsaws. It is an identical replacement for a missing or a damaged retainer that is utilized to secure the piston pin. To ensure the exact location and the correct application of this product, refer to the appropriate diagrams for yo...Read moreur specific model. Keep in mind this high-quality hardware is made of durable metal and is sold as an individual item.