This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.
The hex bolt attaches to the washer and the square key. This part is an OEM from Craftsman for use in snowblowers and lawn mowers. It is available as an individual replacement part and is made of metal. If this item becomes broken or stripped it will need to be replaced and may require a socket set during the installation.
This hinge pin is an OEM part that is designed to hold the chute to the bracket of your lawn mower, allowing the shute to move upward and downward. It is silver, made of metal, and it is around 5 inches in length. Over time, the hinge pin may break, and it will no longer be able to support the chute or allow it to move.
If this occurs, ...Read moreyou will need a pair of needle nose pliers to complete this simple repair, which most of our customers told us was easy. Look for the hinge pin on the chute door and the mounting bracket of your mower deck.
This is the lower handle for various models of walk-behind lawn mowers. This handle is made of durable black metal and attaches directly to the rear of the lawn mower. This handle is an OEM part that is sold by itself and does not come with any hardware or other parts. If your current lower lawn mower handle is corroded or damaged, it nee...Read moreds to be replaced immediately so you can properly and safely handle your lawn mower. This handle measures approximately 24.5-inches long and 17-inches wide and connects the rear of the lawn mower with the upper and main handle that the user holds when operating the lawn mower. Replacing this handle will not require any tools but must start with turning off the lawn mower. Loosen and remove the knobs around the handle, including the ones connecting the lower handle to the mower and those securing the upper and lower handles. Once each knob is removed, replace the old lower handle with the new one, and resecure • all the knobs onto the handle(s).
This centerlock nut, or lock nut, is sold individually and locks itself in place when inserted, to prevent it from backing out due to vibration. Over time, due to its strenueous job, it may become loose or break due to wear and tear, and will need to be replaced. This lock nut is made of metal and is silver in color. When it will no longe...Read morer lock, you will need to complete this easy repair, which requires a wrench or socket and torque wrench.
Ensure you torque the lock nut to your manufacturer specifications; this nut can have a range of different applications for a variety of equipment, so please check your model number or owners manual to be sure it is the right fit for your model.
This silver metal lock washer helps prevent the nut on the drive belt pulley shaft from backing off during operation, it has a 5/16-inch inner diameter and a 1/2-inch outer diameter. one washer is included, replace it if fatigue or damage allows the connected shafts to spin freely, verify fit using the equipment model or owner manual
This genuine OEM carriage bolt is used to secure various parts in lawn and garden outdoor equipment. The bolt has a round head with a square area underneath it that prevents the bolt from turning and coming loose when it is installed. The bolt shaft has a diameter of 5/16 inches, with 18 threads per inch and the threaded portion of the bo...Read morelt is 0.62 inches long. If the bolt is corroded, the threads are worn down, or the head is damaged or deformed, you will need to replace the bolt to keep your equipment parts secured and functioning efficiently. To replace the bolt, first remove the nut using a wrench or socket. Once the nut is removed, you can unthread the bolt. Insert the new bolt in position, thread the nut on and use a wrench to tighten it. Be careful not to overtighten the bolt to avoid damaging it or stripping the threads. This carriage bolt is sold individually.
This is a genuine manufacturer-sourced component which is specially designed for lawn mowers. This is the box that the throttle cable is connected to. The cable connects to the carburetor and it stops the engine when you shift the lever to the full choke position. To ensure the correct repair procedure, refer to the appropriate diagrams f...Read moreor your model. Keep in mind this high-quality throttle box is sold as an individual item. It includes the housing, the trigger, and the hardware to secure these components. A screwdriver will be needed to perform this repair.
It is an authentic component which is specially designed for Little Wonder equipment. This is an identical replacement for a damaged or a missing wheel that was installed on a new unit. It helps to support the equipment allowing for easy transportation. This high-quality wheel assembly is sold as an individual item. Check the diagrams for...Read more your model to ensure the correct repair procedure. A wrench will be needed to replace this wheel. Note, the hardware to secure it is sold separately.
This quarter-inch Nylock nut, or hex nut, is silver in color and sold individually. Made of metal, its simple task is to secure and lock parts in place on a variety of different equipment. Regardless of the specific function, this nut may become damaged over time and if you notice the part it is securing becoming loose, it is time to chan...Read morege the Nylock Nut.
Use a wrench to make this repair, ensuring your torque to the manufacturer specs.
Most of our customers found this to be an easy repair, but difficulty can vary depending on the part you are accessing to make the repair.
This is a genuine OEM sourced replacement part that is intended to be used with walk-behind lawnmowers from MTD, Yard Machines, Bolens, and Yard-Man. The wheel attaches to the height adjustment plate at the front of the mower. The wheel is used to provide traction to allow the mover to move across the lawn.
This is a genuine replacement part manufactured for use with outdoor power equipment. The screw includes a lock washer and is commonly used to secure the motor to the frame. This screw has various applications based on the model of the machine it is used with. The screw is sold as an individual replacement part, please see model diagram for part location and usage.