Compatible with over 150 models of lawn equipment, this Spark Plug has been sourced directly from the original manufacturer. It is sold individually, made of metal and ceramic components, and is not part of a kit or assembly. The spark plug is used to ignite the air-fuel mixture inside the combustion chamber.
You may need to replace the...Read more Spark Plug if your 1 cylinder engine won't start, or if your more-than-1 cylinder engine runs rough. Spark Plugs will wear over time and should be inspected regularly.
Customers rate this repair as Easy.
This check valve, also known as a one-way valve, is a genuine OEM part that regulates the flow of fuel/oil in the equipment engine to prevent it from flowing backwards. It is made of plastic and designed for use in a variety of lawn and garden power equipment. If the valve is jammed, worn down, or contaminated with dirt and debris, it wil...Read morel be unable to open and close properly, thus restricting the flow of fuel and compromising the engine combustion process. You will likely notice fuel leaks around the carburetor, engine stalling, hard starting, and overall lower performance from your equipment. To remove the faulty valve, carefully disconnect any hoses or fasteners connected to it. Place the new valve in position and secure it appropriately.
This authentic OEM rim sprocket in your chainsaw transfers power from the engine to the cutting chain. It is typically located at the center of the clutch drum, situated at the end of the engine crankshaft. By engaging with the chain drive links, it enables the chain to rotate and cut through materials as the engine turns. You will notice...Read more that if the rim sprocket is broken that the chain slips, does not engage, or rotates unevenly. It may also reveal signs of wear such as worn-out teeth. Failure to replace a broken rim sprocket can result in reduced cutting power, chain damage, and increased strain on the engine. To remove the rim sprocket, first, loosen the chain tension by adjusting the tensioning screw or knob. Then, remove the guide bar by loosening the nuts or clips on the side cover and sliding the guide bar off the saw. Use a screwdriver or appropriate tool to remove the screws or fasteners securing the clutch cover. With the clutch cover removed, you can access the clutch drum. Hold the drum in place and turn the retaining bolt counterclockwise to loosen it. Carefully slide off the clutch drum. This replacement part is sold individually.
This M8 flange nut secures the guide bar and chain assembly in place, ensuring proper alignment and safe operation of your equipment. Designed with an integrated flange and anti-slip teeth to resist loosening from vibration, it provides a reliable, secure hold during heavy use. Made from durable, corrosion-resistant steel with an M8 threa...Read mored and 1.25?mm pitch, replacing a worn or missing nut helps maintain stability and dependable performance.
This is a genuine OEM part. The retaining ring is made for use with many chainsaws, and is used to help secure clutch drum components. The hardened metal component is sold individually. A hex key, screwdriver and pair of pliers are often required for the repair.
This item is a genuine Husqvarna replacement part and it is sourced from the original manufacturer to be used with chainsaws. The metal bushing fits into the connection point on the bottom of the handguard and is used to aid the bolt in securing the guard. This item is available as an individual part.
This is a genuine OEM supplied replacement hardware that is specially made for use with Husqvarna and Poulan chainsaws. It helps to distribute the pressure evenly between the connecting pieces, for correct location and use of this item make sure to check appropriate diagram of your model. This part is made from high quality metal and it is sold individually.
This part is an OEM from Husqvarna. The protective clutch drum bearing is compatible with many chainsaw devices. The metal part is fitted between the clutch assembly and the crankshaft. This item is sold individually. A hex key and a pair of pliers are helpful for the replacement.
This is an authentic OEM part. The Husqvarna chain catcher is compatible with many chainsaws. The metal component is a safety feature, providing protection from a damaged or broken chain. The chain catcher is fastened to the crankcase assembly. Please note the screw used to secure it is sold separately. The chain catcher is sold individually. A hex key is often required for the installation.
This is a genuine OEM sourced replacement hardware, not an aftermarket imitation. It is specially made for Husqvarna chainsaws. This screw is generally used to secure the starter housing. Please note, this torx screw is sold individually. To install or remove this hardware you can use either a flat-head screwdriver or a torx screwdriver.
This cylinder plug is an original part from Husqvarna. Compatible with many chainsaws, the metal plug is sold individually. Fitted in the cylinder, this item covers the compression hole. Pliers may be required for the installation.
This chain pad is supplied directly from the original equipment manufacturer. The plastic pad is compatible with many chainsaws. This component is fitted in the clutch cover assembly, providing protection from the wear of the chain. A screwdriver, pair of pliers and a socket set are often helpful in making the repair. The chain pad is sold individually.