365-SUB MTD Engine - Overview

This high-quality fuel bowl O-ring is a genuine replacement part supplied by the original equipment manufacturer for use with lawn and garden equipment. It is designed to create an airtight seal for the fuel bowl, helping to prevent leaks and maintain proper engine performance. Over time, the O-ring may shrink, crack, or degrade, requirin...Read moreg replacement to ensure continued reliability. Made from durable rubber, this part is sold individually and includes one O-ring per order.

This key a genuine manufacturer-sourced replacement part for use with outdoor equipment. They key is inserted into the ignition to power on the equipment. It is made of durable plastic and is approximately 1 inch wide and 2.25 inches long. You will need a replacement key if yours is broken or lost. Each key is sold individually.

This fuel tank assembly is a genuine replacement part supplied straight from the manufacturer. It is commonly used in snowblowers. This tank is designed to contain the fuel needed to power the machine. It should be replaced if it is damaged or begins to leak. Before replacing this part, first be sure to empty the fuel tank.

The fuel tank nipple, also referred to as a fitting, connects the fuel tank of your lawn equipment to its engine fuel line, allowing fuel to reach the engine. If you observe fuel leaks or a loose connection, the nipple may be damaged and requires replacement. When removing the old fuel tank nipple, ensure the tank is empty and the engine ...Read moreis turned off. Use a wrench or pliers to detach the nipple. This high-quality OEM replacement part is sold individually.

This genuine carburetor gasket plate is an original replacement part sourced directly from the manufacturer for use in snowblowers by MTD, Yard Machines, Troy-Bilt, Yard Man, and Cub Cadet. Positioned between the carburetor and the choke control bracket, this component is essential for creating a secure, airtight seal that ensures proper ...Read moreengine performance. Made from a thin, durable material, the gasket plate may require replacement if it becomes damaged or worn. This item is sold individually and may require a socket set and pliers for installation. For best results, consult your equipment’s service manual and perform the repair with the engine off and cool.

A choke control bracket is designed to mount a choke lever/knob, allowing you to open or close the choke whenever necessary. This bracket is designed for use with snowblowers and is made of high-quality metal and features a built-in choke lever and connects to a push rod which actuates the choke on the carburetor. If you find that you hav...Read moree little-to-no control over the choke, or that the choke engages and/or disengages at random, this bracket may be damaged or worn and need to be replaced. To replace this bracket, you will need a screwdriver and wrench to access the inside of the carburetor housing, disconnect and replace the bracket, and reassemble the entire housing. This bracket is sold as an individual and is a genuine OEM part.

This part is an OEM from MTD for use with Snow Blowers and Engines. The Choke push rod connects the choke thermostat lever to the carburetor choke plate lever to control airflow through the carburetor during engine start-up. The most common reason for replacing the choke link is if the engine will not run smoothly or will not start at all...Read more. This part is sold individually. The tools that you will need to replace the choke push rod is a 5/16 inch socket or nut driver.

A frayed pull cord, loose handle, or rope that stays extended can make a small engine hard to start. A complete recoil starter replaces the housing, pulley, spring, rope, and grip as one unit. First check that the engine turns freely and that the starter cup is not bent or worn. Match the assembly to the full engine model, type, and code....Read more Remove the spark plug wire and allow hot parts to cool before service. Install every fastener securely, keep the rope clear of sharp edges, and test the rewind action slowly before starting the machine.

This mounting bolt seals the fuel system and keeps the fuel bolt securely attached to the carburetor in a variety of gas-powered outdoor equipment. It is a genuine OEM part made of metal with dimensions of 0.25-20 x 0.875 inches. If you notice that the bolt is corroded or rusted, it will need to be replaced. A faulty or loose mounting bol...Read moret may cause fuel to leak, make it difficult to start or run your equipment engine, and may allow contaminants to enter the engine. The bolt is easy to install using a wrench or socket. Be careful not to overtighten the bolt as this may damage the fuel bowl. Each item is sold individually.