36358072894 Kenmore Refrigerator - Overview

This drawer slide rail is for the right side of your refrigerator. The drawer slide rail attaches horizontally to the refrigerator wall and supports the drawer so it can easily slide in and out. If the drawer slide track is broken, not sliding, or the fridge is not dispensing water, replacing this part could solve the issue. Make sure to ...Read moreunplug the refrigerator from the power source and wear gloves to protect your hands when installing this part. Refer to the diagram provided by the manufacturer for further guidance and instruction.

This is a manufacturer-approved drawer slide rail for your refrigerator. This slide rail is for the left side of the fridge. All you need to complete this repair is a Phillips screwdriver. Remove the shelves above and below the slide rail so you have room to access it. Unscrew the slide rail and replace it with the new one.

This 10 by 5 inch ice maker (Electromechanical Icemaker Kit, Ice Maker Assembly) produces ice. This particular model will produce seven crescent shaped cubes every cycle. It is constructed of plastic and metal, and comes in black/white. This kit includes a set of installation instructions, a 4-pin round plug-in connector, 6 post plug-in c...Read moreonnectors, tube and fill cup. The ideal temperature of a freezer is zero degrees Fahrenheit. If the temperature in your freezer is at an appropriate level yet ice is still not being made, it could be an issue with the water inlet valve or your ice maker assembly. If you determine it is the ice maker, this is the replacement you need. The ice maker can break from normal wear and accidental damage. Ice makers will need to be replaced every 3-10 years depending on the frequency of usage and water quality. This model is mounted on the freezer wall.

This “Dispenser Door Assembly” (Door Recess Assembly, Ice Door Assembly, Dispenser Door, Refrigerator Dispenser Ice Chute Door Kit, Dispenser Door Flap, Ice Chute Door, Flapper) keeps the room air from infiltrating the freezer. Once the lever is pressed, the door flap opens and allows the ice to dispense into your container. If your door...Read more flapper is broken, it could allow outside air to enter the freezer and alter the inside temperature. You may notice frost buildup surrounding the dispenser area. The door flap can disconnect from the dispenser lever, or the tabs that hold it in place may break. Frequent use may distort the sealing face and cause air leaks and frost buildup. This part mounts in the ice dispenser, and measures approximately 3.25 inches in diameter. It is constructed of plastic and rubber, and comes in white/black. This part is sold individually.

Sold individually.

The defrost heater keeps the cooling coils from frosting over. The heater will get hot and melt any ice or frost build up around the coils.

Quick connector for plastic water line - 5/16" to 5/16"

This evaporator fan motor grommet, or condenser fan grommet is built for refrigerators. It provides a cushion between the fan motor and the motor mounting bracket. It is made or round, black plastic and is approximately one inch in diameter. If your grommet is torn or damaged and you are getting noise from the fan motor, you may need to replace it. This is an OEM part sourced directly from the manufacturer.

This right-side drawer slide rail is designed to support and guide the bottom shelf drawer within the refrigerator compartment, ensuring smooth and stable operation. It serves as a direct replacement for worn or damaged slide rails that may cause the drawer to feel loose or difficult to open and close. Engineered for durability and precis...Read moree fit, this component helps maintain proper alignment and functionality of the drawer system. Installation typically involves removing the drawer, detaching the old rail, and securing the new one in place to restore optimal performance.

This device acts like a clock. It continually advances and alternates between activating the cooling cycle and the defrost heater.

This drawer slide rail is for the left side of the refrigerator, and allows the bottom shelf to slide in and out. If your refrigerator door will not close, or the bottom drawer will not slide properly, you may need to replace the slide rail. Make sure the slide rail that is damaged on your refrigerator is on the left side before you selec...Read moret this part. The slide rail is made of white plastic and connects to the side of your refrigerator. It is sold individually, and is an OEM part sourced directly from the manufacturer.

It is used with those refrigerators that have an ice and water dispenser in the door.