Models
>
3634272790
3634272790 Kenmore Cooktop - Overview
Sections of the 3634272790
[Viewing 2 of 2]
Manuals & Care Guides for 3634272790
Click to downloadKeep searches simple, eg. "belt" or "pump".
Surface Element - 8 Inch - 2350W
PartSelect #: PS243868
Manufacturer #: WB30M2
The surface element, also known as the coil surface element, transfers heat to the area on top of range. The element is 8 inches in diameter. If your surface element does not heat, over heats, or heat...
$61.79
In Stock
Drip Bowl - 6 Inch
PartSelect #: PS244800
Manufacturer #: WB32X5075
This 6 inch chrome drip bowl is intended for use with solid terminal plug-in style surface burner units on electric ranges.
$9.15
In Stock
Surface Element - 6 Inch - 240V
PartSelect #: PS243867
Manufacturer #: WB30M1
If you notice that your surface element will not heat properly, you may need to replace it. This surface element is 6 inches in diameter and 240V. It is a Y-frame surface burner element with five turn...
$57.41
In Stock
Drip Bowl - 8 Inch
PartSelect #: PS244801
Manufacturer #: WB32X5076
This 8 inch chrome drip bowl is intended for use with solid terminal plug-in style surface burner units on electric ranges.
$12.66
In Stock
Terminal Block
PartSelect #: PS232646
Manufacturer #: WB17X5113
This kit includes one ceramic block with 6" wire leads, 2 wire nuts and 2 heat shrink with mounting bracket.
$38.38
In Stock
Porcelain Drip Bowl - 6 Inch
PartSelect #: PS244375
Manufacturer #: WB31M20
This is a replacement drip bowl for your range. It is black in color and is approximately 6 inches in diameter. The bowl is made of porcelain and is sold individually. The drip bowl rests under the bu...
$8.03
In Stock
Porcelain Drip Bowl - 8 Inch
PartSelect #: PS244373
Manufacturer #: WB31M19
This 8" drip bowl is intended for use with loop style surface mount burner element units.
$10.87
In Stock
Grease Filter
PartSelect #: PS243130
Manufacturer #: WB2X8422
Used with a 30" range hood. Sold individually.
No Longer Available
Switch Seal
PartSelect #: PS243590
Manufacturer #: WB2X9504
This part goes between the infinite switch (under the cooktop) and the knob.
$32.19
In Stock
Element Disc
PartSelect #: PS244021
Manufacturer #: WB30X260
This is an element disk but may also be known as a surface element and it is a part for your range. The function of this disk is to give heat to the cooking area on top of the range. This disk is for ...
No Longer Available
Infinite Burner Switch
PartSelect #: PS236434
Manufacturer #: WB23X10009
Sold Individually. Order quantity required.
No Longer Available
Questions And Answers for 3634272790
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 3634272790
[Viewing 2 of 2]Element will not heat
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replacement of Coils
Removed by slightly wiggling out of the coupling. No tools needed, seriously, (and I'm a contractor). Basically, pull out and snap back in.
Parts Used:
-
Joseph from South Plainfield, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
35 of 42 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heating element required continuous adjustments to work.
I removed old 8" surface element and terminal block. Some of old wiring had to be cut off because of harding/cracking of old wiring. Stove was 23 years old and this burner was the most frequently used one. I soldered the new and remaining old wires together. I used the shirnk wrap that came with the terminal block to cover the solder join
... Read more
t. I screwed the new terminal block (one screw holds it in place - used same screw from old terminal block that was removed). I finished by inserting the new surface element. Everything works fine. In the next week or two after we use it a while, I will check wiring again to make sure there are no changes. You need to be very careful as it gets very hot under the burner.
Read less
Parts Used:
-
Richard from Apex, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
29 of 32 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Large burner very slow heating
Downdraft stove is over 20 years old, but everything else works fine and it would be a real pain to replace it.
This quick-heat back burner is part of a two burner plug- in unit which takes up half of the top of the stove.
I removed the top from the rest of the unit easily removing five screws. Because of the age an ... Read more d long use it was tough getting the old nut off which holds on the disc, but with the help of some spray lubricant it came off. The old wire ends were also rusted, and to get them off I bent up the old holder, which was going to be discarded anyhow. It was a simple matter to plug in the new unit, tighten the nut, clean up the lubricant with a paper towel, and reassemble the unit, which I cleaned inside since it was dusty. After plugging in the unit I turned on the burner...it works like new and has saved me a very costly replacement. I like it so much that even though the front element works perfectly I am considering buying that disc too just so they will match. Finding your company was absolutely great, and I would recommend you to anyone looking for parts. I still have the manual for this stove so I would feel confident in replacing pretty much any part needed....not bad for a 72 year old woman, (My Dad taught me to do my own work and I am a passable carpenter and plumber; a little more wary when it's something electrical !
This quick-heat back burner is part of a two burner plug- in unit which takes up half of the top of the stove.
I removed the top from the rest of the unit easily removing five screws. Because of the age an ... Read more d long use it was tough getting the old nut off which holds on the disc, but with the help of some spray lubricant it came off. The old wire ends were also rusted, and to get them off I bent up the old holder, which was going to be discarded anyhow. It was a simple matter to plug in the new unit, tighten the nut, clean up the lubricant with a paper towel, and reassemble the unit, which I cleaned inside since it was dusty. After plugging in the unit I turned on the burner...it works like new and has saved me a very costly replacement. I like it so much that even though the front element works perfectly I am considering buying that disc too just so they will match. Finding your company was absolutely great, and I would recommend you to anyone looking for parts. I still have the manual for this stove so I would feel confident in replacing pretty much any part needed....not bad for a 72 year old woman, (My Dad taught me to do my own work and I am a passable carpenter and plumber; a little more wary when it's something electrical !
Read less
Parts Used:
-
Drusilla from Bloomfield, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
19 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!