EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

36315121100 Kenmore Dishwasher - Overview

Diagrams for 36315121100

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Piston and Nut Assembly – Part Number: WD24X10018
$32.63
In Stock
Piston and Nut Assembly
★★★★★
★★★★★
(19)
Part #WD24X10018
This is used for the check valve.
Door Gasket - White – Part Number: WD08X10057
$79.71
In Stock
Door Gasket - White
★★★★★
★★★★★
(21)
Part #WD08X10057
This one piece dishwasher door gasket provides a water tight seal to keep water from leaking out of your dishwasher.
Water Inlet Valve – Part Number: WD15X10003
$78.26
In Stock
Water Inlet Valve
★★★★★
★★★★★
(16)
Part #WD15X10003
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed. This valve has a 3/8" inlet and comes with the mounting bracket.
Rinse Aid Fill Cap – Part Number: WD12X10284
$34.74
In Stock
Rinse Aid Fill Cap
★★★★★
★★★★★
(14)
Part #WD12X10284
This part helps keep the rinse aid the dispenser until its needed.
Hinge Arm Link – Part Number: WD14X10009
$16.05
In Stock
Hinge Arm Link
★★★★★
★★★★★
(9)
Part #WD14X10009
The hinge link on your dishwasher connects the spring to the dishwasher door hinge. If the hinge link becomes cracked or damaged, you may not be able to shut or lock your dishwasher door properly. In this case, you will need to replace the hinge link. Pull out your dishwasher to inspect the hinge and spring, if the link is broken, it may be disconnected and on the ground already. If not, you can remove the hinge arm link by simply disconnecting it from the hinge and spring, then replacing it with the new part. The hinge arm link is a small piece of white plastic about an inch and a half long. It is sold individually, and is an OEM part from the manufacturer.
Drain Solenoid Kit – Part Number: WD21X10060
$63.64
In Stock
Drain Solenoid Kit
★★★★★
★★★★★
(6)
Part #WD21X10060
This kit includes the armature and linkage assembly.
Motor and Pump Kit – Part Number: WD26X10013
$198.71
In Stock
Motor and Pump Kit
★★★★★
★★★★★
(12)
Part #WD26X10013
This is a pump and motor kit for your dishwasher. This assembly replaces many old-style pump and motor kits that were manufactured since 1970. The instructions are included with this kit in to assist you. Take note that this is a completely redesigned kit by the manufacturer and now includes the drain solenoid. You may need to replace this part is if your appliance is leaking, not draining properly, noisy, or will not start or clean your dishes properly.
Impeller and Seal Kit – Part Number: WD19X10032
No Longer Available
Impeller and Seal Kit
★★★★★
★★★★★
(5)
Part #WD19X10032
The impeller and seal kit is used in a dishwasher. The kit includes all the parts needed to do this repair, including the impeller, seal, blade, filter, skidder and skidder holder. If your washer is leaking, not cleaning dishes properly, or not draining, then replacing some parts in the pump can help solve the issues mentioned. The tools needed for this installation project are: 5/16 nut driver, 1/4 inch nut driver, flat-blade screwdriver, Phillips screwdriver, and pliers. Refer to the manual provided by the manufacturer for installation instructions and accurate guidance. Remember to unplug your dishwasher from the power source and wear work gloves as a safety precaution.
Detergent Cup Release Arm – Part Number: WD16X10011
$28.42
In Stock
Detergent Cup Release Arm
Part #WD16X10011
This is the replacement detergent cup release arm for your dishwasher. It is made of black plastic and is sold individually. The detergent cup release arm is found on the inside of the dishwasher door, and it is the part that releases both the detergent and the rinse-aid. If the rinse-aid and detergent are not being released during the dishwasher cycle, or you notice that the release arm is cracked or damaged, then you will need to replace it. A damaged detergent cup release arm can also lead to a door latch failure on your dishwasher, and it may cause the dishwasher not to start. This is an OEM part sourced directly from the manufacturer.
Door Latch Kit – Part Number: WD13X10003
$47.40
In Stock
Door Latch Kit
★★★★★
★★★★★
(10)
Part #WD13X10003
This door latch kit is used for dishwashers.
Drain Hose – Part Number: WD24X10014
$47.40
In Stock
Drain Hose
★★★★★
★★★★★
(4)
Part #WD24X10014
This drain hose is an OEM, manufacturer-approved replacement part for your dishwasher. The drain hose filters out the wastewater from the dishwasher. If there is a hole in it, water will leak out of your dishwasher. Shut off the water and power to the unit before beginning this repair. Accessing the drain hose involves unscrewing the dishwasher and pulling it out. Remove the clamp holding the hose in place to its connection under the sink, using a 5/16ths socket. Disconnect the fill line. Use a 1/4 inch nut driver to loosen the clamp at the other end of the drain hose. Keep a towel handy for any water still inside. Keep the clamps for use on your new drain hose. Reinstall all hoses and lines in reverse order.
Finished Access Panel – Part Number: WD27X10225
$49.50
Special Order
Finished Access Panel
Part #WD27X10225

Manuals & Care Guides for 36315121100

Click to download

Questions And Answers for 36315121100

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Todd - For model number 36315121100
June 29, 2025
I need the parts for the top rack on the metal guide that slides back-and-forth that attaches to the rack With all white cap slides onto the rack on both sides is wore out in the rack wants to fall down now
Chris Boyle Profile
Hello Todd, thank you for reaching out. If you are looking for the upper rack slide, then it is listed on our site with part number PS261576. We hope this helps!
$62.60
In Stock
Upper Rack Slide
Was this helpful?
Thank you for voting!
  • 1

Common Symptoms of the 36315121100

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dishwasher wouldn't fully drain
191 of 206 people found this instruction helpful.
  • Dan from Minnetonka, MN
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I removed the four screws holding the screen and molded plastic cage inside the rear of the dishwasher to expose the check valve assembly. I then unscrewed the piston and nut assembly with my hand and replaced it with the new one. I found that the rubber cone shaped valve on the old piston and nut assembly was entirely disintegrated. T his easy repair solved the problem.
Was this helpful?
Thank you for voting!
Dish washer is not running through cycles
93 of 108 people found this instruction helpful.
  • mike from huntley, IL
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Wrench (Adjustable), Wrench set
First and formost before you buy read everything in trouble shooting your dishwasher. Then you do not buy parts you do not need. First you turn off power, then water. Remove two screws, a rubber hose and a hard line by unscrewing if you are lucky some contractors might sweat this on. No biggie just two extra steps that's all. do in reve rse to assemble...
Was this helpful?
Thank you for voting!
D/W would not drain. Water standing in bottom.
65 of 71 people found this instruction helpful.
  • Ed from Cornelius, NC
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
It is a simple process to replace the drain solenoid on these dishwashers, having replaced several in the past few months.

After removing the front bottom panels, I removed the 2 screws holding the old solenoid, unplugged the wire harness, and then switched over the springs to the new solenoid. Assembly was installing 2 scre ws, and plugging in the wire harness.

I work on a 260 + unit property, as well as working for a property management company who rents single family homes.

PartSelect.com is an excellent source of parts, shipping in a quick manner, allowing the repairs to be completed in a timely manner. Thank you.
Was this helpful?
Thank you for voting!