Models
>
36275876691
36275876691 Kenmore Range - Overview
Sections of the 36275876691
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Flat Style Oven Igniter Kit
PartSelect #: PS231280
Manufacturer #: WB13K21
The flat style oven igniter kit comes with a mounting bracket and a wire connector with a plug. The igniter kit is used to light the oven burner. If you notice that your oven will not heat up properly...
$62.23
In Stock
Oven Rack
PartSelect #: PS6447646
Manufacturer #: WB48T10095
The oven rack is sold individually. It is chrome in color and measures approximately 24 inches wide by 17-1/2 inches deep. The rack is used to hold cookware in the oven and slides back and forth for e...
$67.42
In Stock
Light Bulb - 40W
PartSelect #: PS217532
Manufacturer #: 40A15
This 40-Watt light bulb is sold individually and is a genuine OEM replacement option for your home appliances. It is specially designed to withstand extreme temperatures, so this bulb is compatible wi...
$11.02
In Stock
Oven Sensor
PartSelect #: PS236043
Manufacturer #: WB21X5301
It is possible that your oven is cold because of a fault in the temperature sensor. The temperature sensor regulates oven temperature in modern ranges, like a thermostat. It is on the back wall near t...
$151.71
In Stock
Surface Burner Spark Electrode
PartSelect #: PS231276
Manufacturer #: WB13K18
This part helps your burner ignite and produce flame.
$41.95
In Stock
Ignitor Mounting Screw
PartSelect #: PS234519
Manufacturer #: WB1X1293
Sold Individually.
$9.64
In Stock
RECEPTACLE PUSH-IN
PartSelect #: PS752188
Manufacturer #: WB08T10026
This part is the replacement light socket for your oven. The oven light socket provides power to the light, and at the same time holds the light bulb in place.
$8.54
In Stock
Light Cover
PartSelect #: PS247415
Manufacturer #: WB36X192
This light bulb lens covers the interior light bulb in an oven, range, or stove. No tools are necessary to replace this part. Simply slide off the wire bracket to remove the existing light bulb lens. ...
$13.53
In Stock
Screw
PartSelect #: PS283515
Manufacturer #: WR01X10065
Size: 10-32 GXTT FLP .595
Sold individually.
$8.06
In Stock
Questions And Answers for 36275876691
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 36275876691
[Viewing 8 of 8]Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Gas smell
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The igniter glowed, but never got hot enough to ignite the propane, so I did smell propane.
First, I removed the two screws that held the heat shield in place. Second, I removed the one screw that held a small wire covering. That covering kept the wires inside the back wall of the range. Third, I removed the two screws that held the Igniter Kit, and unplugged it from the back of the range. I then carefully put the new ignite
... Read more
r in, and reassembled everything in reverse order. It only took about 30 minutes to do the repair, and 30 minutes of cleaning and wiping of the broiler area. (It is amazing what you see when you take things apart). I should have been wiping things up over the past few months. Overall, a very easy repair. I ordered the part at 12:30 in the afternoon, and FedEx delivered it the next morning at 11:30, all for the regular shipping price of $6.95. VERY HAPPY.....
Read less
Parts Used:
-
Sidney from Marysville, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
671 of 718 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven would not light or keep temp.
first I thought it was a faulty gas valve, so I pulled it out, started researching for a replacement part, found your site and started research. I discovered thhat the igniter was the culprit, that info. saved me about a week of time and a 100 bucks, so I installed the gas safety valve back in the oven, patience is the word for the day,
... Read more
you cross thread this and you are done! any way ordered ignighter and it shipped to my house in about 4 days, New York to Calif. had it installed in about 15 minutes fired off the oven and ...IT worked hurray...10-9-2010,
Read less
Parts Used:
-
zack from corning, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench set
448 of 461 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven wouldn't heat. This degraded over several weeks.
1. Pulled the 110V power plug. It was not necessary to turn off the gas; just be careful not to stretch or pinch the flexhose behind the stove.
2. Removed the oven door by opening a couple of inches then lifting upward.
3. Removed the warming drawer by pulling out to the stop, then pushing the small levers on the side of the t ... Read more rack to release.
4. Removed two flathead screws at the back of the oven to free up the oven bottom panel.
5. Removed the bottom panel by lifting up the pack until the front edge clears the overhang.
6. Removed the two screws on the side that hold the igniter to the burner tube. Be sure not to let the screws drop into the gaps in the oven floor. Note the position of the bent tab with the holes to ease aligning the new part.
7. Reached through the warming drawer to release the plug by squeezing the tabs on the end.
8. Pulled the plug up through the gap in the oven floor (where the wires went through) and connected it to the other connector.
9. Ran the new wire down through the oven floor.
10. Aligned the new igniter and tightened them. Had trouble getting the screws started so I used a toothpick to align one hole while starting the other screw.
11. Replaced the oven bottom panel. It needed a little jockeying to get the screws and holes aligned.
12. Replaced the door.
13. Replaced the oven drawer.
This turned out to be a good time to clean all those dusty places that don't get cleaned that often.
2. Removed the oven door by opening a couple of inches then lifting upward.
3. Removed the warming drawer by pulling out to the stop, then pushing the small levers on the side of the t ... Read more rack to release.
4. Removed two flathead screws at the back of the oven to free up the oven bottom panel.
5. Removed the bottom panel by lifting up the pack until the front edge clears the overhang.
6. Removed the two screws on the side that hold the igniter to the burner tube. Be sure not to let the screws drop into the gaps in the oven floor. Note the position of the bent tab with the holes to ease aligning the new part.
7. Reached through the warming drawer to release the plug by squeezing the tabs on the end.
8. Pulled the plug up through the gap in the oven floor (where the wires went through) and connected it to the other connector.
9. Ran the new wire down through the oven floor.
10. Aligned the new igniter and tightened them. Had trouble getting the screws started so I used a toothpick to align one hole while starting the other screw.
11. Replaced the oven bottom panel. It needed a little jockeying to get the screws and holes aligned.
12. Replaced the door.
13. Replaced the oven drawer.
This turned out to be a good time to clean all those dusty places that don't get cleaned that often.
Read less
Parts Used:
-
Durwood from Suffield, CT
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
307 of 402 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!