36261101000 Kenmore Range - Overview

This drip bowl, also known as the drip pan or burner bowl, is 6 inches in internal diameter to match the burner, but actually measures closer to 8 inches in total diameter to its outer edges. This authentic manufacturer-approved part is used to catch spills from cooking on the top burner. If your bowls are getting stained, dirty, or rust...Read moreed, this replacement can solve it. First, remove the element from the stove top, and pull out the old drip pan. Insert the new bowl and make sure it is aligned to where the element is plugged in. Lastly, you can put the element back in. For safety precautions, make sure to unplug the range from the power source and wait until the surface is cool before replacing this part. This part is sold individually, if you are replacing more than one drip bowl on your stove at once, you will need to account for this. To replace, simply pull the old surface elements and burner bowls off, give everything a thorough clean, and install the new parts with no tools necessary.

This Drip Bowl, also known as a burner bowl or drip pan, is made to fit an element 8 inches in diameter and comes in chrome. The actual total diameter of this drip bowl is closer to 10 inches, but don't worry, it will fit your 8-inch burner. This bowl is used to catch drippings and food that falls when cooking on the oven element. The dri...Read morep bowl might burn, become rusty, and wear down over time, and will need to be replaced. Replacing the drip pan is very easy. The elements on the oven must be removed to access the pan underneath. When replacing the bowl, make sure to line up the hole with the terminal block where the element plugs into, and always remove power to your appliance and ensure it is completely cool before commencing your repair. These drip bowls are sold individually, not as a set for your appliance, so you will need to purchase each separately if upgrading all the drip bowls for your range.

The bake element is located on the bottom of the oven. If your oven will not heat properly it may be due to a faulty or damaged baking element. If you can see that the element has been separated or blistered, you should replace the part immediately. If there is no visible damage, turn the oven on and check to see if the element heats even...Read morely. If the element is not heating evenly, or if it is not heating at all, it will need to be replaced. This element is 19 inches wide x 19 inches long, and has male spade push on terminals.

This kit includes the female contact with wires, terminal block and mounting clip.

The oven rack is sold individually. It is chrome in color and measures approximately 24 inches wide by 17-1/2 inches deep. The rack is used to hold cookware in the oven and slides back and forth for easy access. Racks can become rough and discolored over time and may need to be replaced, or perhaps you just need extra storage space in the...Read more oven! This repair is extremely simple and does not require any tools. Before you begin, ensure that the rack edges are straight and have not warped from shipment. Once the oven door is open, the stop end goes in first and it simply slides into place.

This broil element is designed for wall ovens and plays a critical role in achieving high-temperature cooking during broil cycles. Positioned at the top of the oven cavity, it delivers intense, direct heat for broiling meats, vegetables, and other dishes. A malfunctioning element may result in the oven failing to reach proper broil temper...Read moreatures, uneven cooking, or complete loss of broil function. Constructed from heat-resistant materials for durability and performance, this replacement part restores optimal cooking capability. Before installation, always disconnect power to the appliance and verify compatibility with your specific oven model.

This large broiler pan is found in the bottom of your oven and is used to catch drippings from broiling foods. This part includes the grate and bottom pan and is made of porcelain. The grate measures 15-1/2 inches wide by 13 inches deep and the pan is about 17 inches wide by 13 inches deep. No tools are required to replace this item, simp...Read morely pull out the lower drawer of your range, pull down the front of the drawer, slide the pan out and slide the new one into place. This is a genuine part sourced right from the manufacturer.

This switch controls the large burner on a range/stove top.

This standard coil element is 6" in diameter with 2 terminal plug-ins.

Have a lawn and garden equipment engine that?s not performing at its peak? You might just need this Craftsman Fuel Tank Kit. This kit is more than a simple replacement part - it?s the helping hand that your engine needs to get back in perfect shape. Here?s why it matters: your engine requires gasoline to run, and this sturdy fuel tank is...Read more where it safely stores that gas supply. Each time you power up your equipment, it's the fuel tank that's working hard behind the scenes to keep everything running smoothly. So, if your engine's underperforming, a new fuel tank could make a world of difference. Installation of your new Craftsman Fuel Tank Kit is straightforward. To make it safe and easy, we recommend working in a well-ventilated area. Start by draining the fuel remaining in your existing tank (always good to avoid unexpected spills!). Remember to also disconnect the spark plug wire before you start ? this is a crucial safety step that can't be overlooked. Rest assured, this is a genuine, brand-approved Craftsman part. We designed it to flawlessly match your gardening power equipment. It promises to restore the robust performance you've come to expect from your Craftsman tools. Invest in your garden's performance with this Craftsman Fuel Tank Kit. It's the straightforward solution you need to get your outdoor equipment running just like new again. Don?t let a worn-out part hold you back. Take the first step towards a smooth-running engine - your garden will thank you for it!

Control your cooktop’s heat with this genuine infinite surface element switch, designed to regulate power to individual burners for precise temperature adjustment. Operating at 1250W and 240V, it allows smooth transitions from low to high heat for consistent cooking results. This durable OEM component helps resolve issues such as burners ...Read morenot heating, overheating, or delivering uneven heat. Installation is simple—disconnect power, remove the faulty switch, and secure the new one in place for reliable performance.