This 25-inch fuel line carries fuel from the tank to the carburetor, ensuring proper engine operation. Made from durable clear plastic, it is designed to withstand regular use but may become clogged or brittle over time. Replacing a worn or damaged line can help prevent leaks and restore reliable starting and performance.
This Genuine OEM fuel filter is designed to maintain the performance and longevity of your equipment by preventing dirt and debris from entering the carburetor. Located inside the fuel tank, this essential component ensures clean fuel delivery, protecting the engine from potential damage caused by contaminants. Sold individually, the filt...Read moreer is built to meet original equipment standards for fit and function. Over time, the filter may become clogged, restricting fuel flow and making engine starts more difficult. For optimal performance, it should be replaced—not cleaned—at the first sign of blockage or wear.
This is the Genuine Craftsman replacement part. It is made out of Flexible Rubber and is Sold Individually. The purpose of the 530069216 Tank Purge Line is to return the excess fuel that is in the carburetor after the primer bulb has been pushed. The excess fuel is forced through the purge line back into the fuel tank. Over time the Tank Purge Line will become brittle and crack and will need to be replaced.
This is a genuine OEM replacement part, it is sold individually. By pressing on the Purge Bulb, it will force fuel into the fuel line from the fuel tank into the carburetor. Once the carburetor is full of fuel, the excess fuel will be purged back into the tank in the fuel return line. Over time the primer will lose its elasticity or crack and need to be replaced. We have an article and video on
Genuine Husqvarna kit. This kit contains the fuel lines, fuel filter and primer bulb and grommet for all of the Husqvarna Blowers listed below. This makes it very convenient when you need all of the separate parts. You can order them in one kit.
Also referred to as a Recoil Spring, this OEM replacement part is used to rewind the pull rope back into the starter housing. This Spring is sold individually, not as part of a kit or assembly, and is made of metal.
If the pull cord will not retract into the housing, inspect the Recoil Spring for signs of wear or damage, replacing if ne...Read morecessary. You will need a screwdriver to complete this repair.
Customers rate this repair as Easy.
This OEM Vacuum Bag holds grass and leaf clippings when the blower is switched to vacuum mode, and is attached to the exit port. It is constructed of white fabric. If broken due to wear/fatigue it will no longer be able to hold clippings and should be replaced. Refer to your make, model and diagrams to see if this is the right part for your machine.
This metal ring in your engine, known as the piston ring, seals the gap between the piston and cylinder wall. It makes sure that the gases produced during combustion do not escape and that the engine maintains the pressure it needs to run. If the piston ring is damaged, oil can seep into the combustion chamber, causing your engine to exhi...Read morebit rough idling and your machine emit blue smoke. To switch out a defective piston ring, detach the old ring from the piston with a screwdriver. When installing the new ring, you may need to compress it to make it fit properly. Please be aware that this genuine OEM replacement part is bought individually. It is recommended that you replace all the piston rings in your machine at once, as they tend to wear down at the same rate. Carefully review your user manual to determine how many rings your machine needs before placing your order.
This is an authentic replacement part supplied from Poulan. It is generally used with gas powered chainsaws. This nut in conjunction with a bolt (sold separately) helps to secure air filter and carburetor. Requires a wrench installing/removing this item. It is sold individually.
This is a standard hardware which has multiple applications based on your tool. It is sourced from original equipment manufacturer for use with a variety of power equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. Requires a hex key or an allen wrench to install or remove it.
This genuine manufacturer sourced replacement part is specially made for use with a variety of handheld lawn and garden equipment. This part is installed on top of the piston/connecting rod. Its purpose is to create a seal in the cylinder so that it can build pressure. A worn or broken piston ring will allow combustion gases to escape the...Read more seal and enter the crankcase, causing low compression and a loss of power. If compression is reduced significantly, the engine will not run at all. Includes one (1) metal piston ring. Tools Required: Receptacle for draining fuel, Torx wrenches, spark plug wrench, 10mm wrench (or adjustable), long-nosed pliers, rubber mallet, standard screwdriver, old starter rope (or similar cord), adjustable pliers, 2-cycle engine oil, razor blade, ignition gapping gauge. • Remove the air cleaner • Drain the fuel • Remove the air cleaner case • Remove the carburetor • Remove the intake insulator • Remove the spark plug • Remove the engine cover • Remove the insulator gasket • Remove the starter assembly • Remove the fuel tank • Remove the air duct • Separate the engine • Bind the engine • Remove the clutch • Remove the flywheel • Remove the starter pulley • Unbind the engine • Remove the muffler • Separate the cylinder from the crankcase • Remove the piston ring • Install the piston ring
This genuine replacement screw is a high-quality OEM part designed for use with Paramount and Poulan gas-powered lawn and garden equipment. It is specifically engineered to secure the starter rope within the pulley, ensuring reliable starting performance.
Made from durable metal, this specialty screw is sold individually.
Installation...Read more Tip: A flat-head screwdriver is required for removal and installation.
For proper placement and application, please refer to your equipment’s model diagram.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Both the Fuel line and the Engine fuel line, where dry rotted.
57 of 75 peoplefound this instruction helpful.
Victor from SCOTTSVILLE, KY
Very Easy
15 - 30 mins
Pliers, Socket set
1) While still attached to the fuel tank, I first sized up the old fuel lines with the newer fuel lines. 2) With a pair of needle nose players, I then removed the old dry rotted fuel ?? lines, from the fuel tank. 3) I cleaned the fuel tank and around the carburetor area, to insure that there was no debris, that could possibly fa
... Read morell into the path of the new fuel lines installation. 4) I then installed the smaller one of the fuel lines, so that it would be out of the way, of the larger fuel line. I Pulled the fuel line through the smaller hole in the fuel tank, with needle nose players. I pulled the smaller fuel line out through the fuel tank filler hole, attached the fuel filter to the smaller fuel line. I Made sure that the fuel filter was extended to the furthest end of the fuel tank bottom. Six inches in all. I then attached the smaller fuel line to the carburetor. 5) I Installed the larger fuel line, followed the same procedures as the smaller fuel line. 6) Both fuel lines where cut on an angle for easy installation. No lubricant was necessary. 7) I filled up the fuel tank with fresh fuel and oil, new air filter and spark plug. It started on the first pull. Amazing.
To start, remove the plastic carburetor grill. DO NOT remove the carburetor. The fuel line has to be sliced down to fit through the tank hole and get it in far enough up into the tank to grab with needle nose pliers.( need long needle nose pliers which I didn't have) I placed about six inches of the plastic tubing in the jaws of vice so t
... Read morehat half of the tube was squeezed in the vice jaws. I then used a razor blade to shave off the exposed tube. I slipped the shaved end of the tube up through the tank hole far enough to grab with long tweezers and pulled it up to where I could grab it in the tank with needle nose pliers. I put light lube oil on the remaining tubing and pulled it through. It takes a steady firm pull to pull it in. Install the filter and pull the tube back down into the tank. I also used a small diameter drill bit and with my fingers slightly reamed the tube ends to ease the tube over the filter and carburetor nipples. To prime the engine, spray starting fluid into the carburetor and start. Repeat until the engine will run on fuel. It took me hours to figure this out, but will take less than an hour with this method.
I still have not received the part lost in shipping
8 of 14 peoplefound this instruction helpful.
Richard from SAINT LOUIS, MO
Really Easy
30 - 60 mins
I have tried to get a hold of you and the shipper (UPS) and have had no luck I am glad that you have finally sent out a survey or questioner, please help Rick 3142207433 [email protected]