This 25-inch fuel line carries fuel from the tank to the carburetor, ensuring proper engine operation. Made from durable clear plastic, it is designed to withstand regular use but may become clogged or brittle over time. Replacing a worn or damaged line can help prevent leaks and restore reliable starting and performance.
This is the Genuine Craftsman replacement part. It is made out of Flexible Rubber and is Sold Individually. The purpose of the 530069216 Tank Purge Line is to return the excess fuel that is in the carburetor after the primer bulb has been pushed. The excess fuel is forced through the purge line back into the fuel tank. Over time the Tank Purge Line will become brittle and crack and will need to be replaced.
This is an authentic OEM replacement kit for use with lawn and garden equipment. Each kit includes the carburetor, cylinder, crankcase, and muffler gaskets. The carburetor gasket seals the area between the carburetor and engine block to prevent the entry of contaminants into the carburetor. The crankcase gasket prevents oil from leaking o...Read moreut of the crankcase. The cylinder and muffler gaskets prevent the combustion and exhaust gases from escaping. If you are experiencing common problems such as leaking, loss of compression, and poor engine performance this indicates that your gaskets may be worn down or damaged and need replacement. Carefully remove the old gaskets and thoroughly clean the mating surfaces where the new gaskets will be installed to ensure a good seal. Install the new gaskets and ensure that they fit properly.
The Fuel Cap Asssembly attaches on top off the fuel tank in order to prevent fuel from exiting, or debris from entering. Installation is rated as "Easy" by customers. If broken due to fatigue/wear/damage, you may notice a fuel leak or the smell of fuel, and the part should be replaced. Refer to your make, model and diagram to ensure this is the correct part. This part is plastic, and comes individually sold.
The chainsaw starter rope is a three-foot-long white rope that is approved by the original equipment manufacturer, and which wraps around the recoil pulley and is pulled to start the engine. Installation is rated as "Easy" by customers and requires a screw driver, pliers, and torx screwdriver. If the rope breaks it should be replaced. Ref...Read moreer to your make, model and diagram to ensure this rope is right for your machine.
This genuine replacement screw is a high-quality OEM part designed for use with Paramount and Poulan gas-powered lawn and garden equipment. It is specifically engineered to secure the starter rope within the pulley, ensuring reliable starting performance.
Made from durable metal, this specialty screw is sold individually.
Installation...Read more Tip: A flat-head screwdriver is required for removal and installation.
For proper placement and application, please refer to your equipment’s model diagram.
This is a genuine OEM replacement clutch drum that is specially manufactured for Poulan and Husqvarna chainsaws. This is the piece beneath the clutch that actually drives the chain. When it wears down, your saw will see a major decrease in performance. A common issue with the clutch drum is erosion of the spindle where the upper drive sha...Read moreft connects to the assembly. The square corners of the spindle become rounded causing the shaft disengage.It is a high quality metal item that is sold individually.
This metering diaphragm is an original part for use in edgers, blowers, trimmers, and chainsaws made by Poulan, Paramount, Weed Eater, Husqvarna, and Jonsered. It fits between the metering diaphragm gasket and the metering diaphragm cover. It is made of a thin material and will need to be replaced if it breaks. A screwdriver may be needed when replacing this part and keep in mind that it is sold individually.
This fuel pump diaphragm, also called a membrane or a gasket, is what helps pump fuel from the tank to the engine of your gas-powered lawn equipment. It is normally found attached to the carburetor assembly itself. You can tell that the diaphragm is broken when your engine is not starting properly, lacks power, or frequently stalls. You m...Read moreay also notice that your machine is leaking fuel or smells strongly of gasoline. A broken diaphragm could lead to engine performance problems, and it may eventually stop working altogether. When replacing your old diaphragm, you will need a wrench to disconnect it from the fuel pump housing. Kindly note that this OEM-sourced component is sold individually.
This is a genuine OEM sourced replacement screw designed for use with Husqvarna and Poulan chainsaws. This screw has multiple applications depending on the tools model. Please make sure to check appropriate diagrams for correct use and location of this hardware. Keep in mind, this Torx screw is sold individually.
This is an original replacement part manufactured for use with chainsaws and leaf blowers. The washer is commonly used to disperse the pressure put on the flywheel by a nut across a wider surface area. This washer is available as an individual replacement part, please see model diagram for associative parts.
It is a genuine OEM sourced replacement screw that is specially produced for use with handheld lawn and garden equipment. This screw is a standard hardware which has multiple applications depending on your unit, for please refer to the appropriate diagrams for the correct location and use of this part. It is a high-quality hex socket head screw which is sold individually.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Split fuel line driving brother-in-law to frustration
1 of 5 peoplefound this instruction helpful.
Howard from UNICOI, TN
Really Easy
30 - 60 mins
Pliers
Seven screw, three case cover, two air cleaner, two carb mounting, pulled carb, drained tank, pulled old fuel line, treaded new one in, wire to thread, thread to angle cut fuel line. Reassemble, test, sharpen chain, retest…not exactly a doityourselfer, graduate degree in mechanical/industrial engineering and former medium/heavy mechanica
... Read morel. Get fuel line on carb prior to reassembly, line may need some stretching with a tapered punch.