This Genuine OEM fuel filter is designed to maintain the performance and longevity of your equipment by preventing dirt and debris from entering the carburetor. Located inside the fuel tank, this essential component ensures clean fuel delivery, protecting the engine from potential damage caused by contaminants. Sold individually, the filt...Read moreer is built to meet original equipment standards for fit and function. Over time, the filter may become clogged, restricting fuel flow and making engine starts more difficult. For optimal performance, it should be replaced—not cleaned—at the first sign of blockage or wear.
The Fuel Line Fitting is a plastic part which attaches two pieces of fuel line together. If broken due to damage/fatigue, there may be a leak and the part must be replaced. Installation is rated as "Easy". Refer to your make, model and diagram to ensure this part is correct for you.
This part is the replacement fuel cap assembly for your chainsaw. It is made of black plastic and is sold individually. The fuel cap prevents fuel from spilling out of the chainsaw and prevents debris from entering the fuel tank. If the fuel cap is stripped or missing the O-ring, it can cause a leak, and will need to be replaced. To repla...Read morece the fuel cap simply screw the old one out and screw the new one in, ensuring you have a tight seal. This is an authentic OEM part sourced directly from the manufacturer.
It is a genuine OEM item that is made for Craftsman chainsaws. This is a special component which helps to provide a tight fit between connected parts. Over time it may wear out, get damaged or lost eventually requiring a replacement. Make sure to check the appropriate diagrams for your model to ensure the proper repair procedure. It consists of three durable metal parts.
Genuine Poulan replacement part, this item is sold individually. The purpose of the Air Filter is to block dust and debris from entering the carburetor and engine and causing damage. Once an Air filter becomes dirty, it constricts the flow of air to the engine making it not run properly. It is advised to keep an extra one or two on hand.
This is an authentic OEM part for use with Craftsman Chainsaws. The recoil starter repair kit replaces the parts of the engine\\\'s recoil starter susceptible to normal wear. The most common reason for replacing the recoil starter repair kit is if the engine won't turn over when starter rope is pulled the Starter rope pulls too easily (an...Read mored without resistance) the Starter hub is not engaging the flywheel or the Starter hub is not turning with the pulley (when the rope is pulled). This part includes starter pulley the assist spring and the starter hub. Here is a list of tools that are needed to install the recoil starter repair kit Phillip's screwdriver, Torx drivers, long-nosed pliers, and scissors or wire cutters (optional).
This is a genuine OEM sourced replacement part designed for use with Poulan chainsaws. It is used to attach the cylinder shield to the main body of the chainsaw. This screw is made out of metal and it is sold individually. To remove or install this screw you would need a T-25 torx screwdriver.
The chainsaw starter rope is a three-foot-long white rope that is approved by the original equipment manufacturer, and which wraps around the recoil pulley and is pulled to start the engine. Installation is rated as "Easy" by customers and requires a screw driver, pliers, and torx screwdriver. If the rope breaks it should be replaced. Ref...Read moreer to your make, model and diagram to ensure this rope is right for your machine.
This is an authentic replacement part supplied from Poulan. It is generally used with gas powered chainsaws. This nut in conjunction with a bolt (sold separately) helps to secure air filter and carburetor. Requires a wrench installing/removing this item. It is sold individually.
This is an OEM part sourced directly from the manufacturer. The chain brake kit is designed for use in Craftsman chainsaws. This part is made of metal and high-quality plastic, and is used to halt the motion of the chain. You may require a screwdriver or Allen wrench when replacing this part. This item is sold individually.
This is a genuine replacement part manufactured for use with chain saws from Craftsman. This part secures the bar to the clutch. It is recommended to review your models diagram to verify the parts compatibility. This bar mounting plate is made of metal and sold individually.
This is a Genuine OEM replacement part used on Poulan Gas Chainsaws. This item is made out of Metal and it is Sold Individually. A centrifugal clutch is a part that uses centrifugal force to connect two concentric shafts, with the driving shaft nested inside the driven shaft. Today's centrifugal clutches will function even when they shoul...Read moredn't, far beyond the point of when they need to be replaced. Keeping an eye on equipment performance will determine when the centrifugal clutch requires attention. Please note Clutch Drums is Sold Separately. To replace this item you would need a Wrench and Pliers.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Worn out oil pump/burning chains
6 of 6 peoplefound this instruction helpful.
William from EVANSVILLE, IN
Really Easy
30 - 60 mins
Screw drivers, Socket set
After checking several different videos, ordered the repair parts and two specialty tools( Clutch removal/install and a worm drive remover/installer) Total for parts and tools around 45.00. Much cheaper than the shop wanted, 85.00 to look at it plus parts. As for results I've used the chainsaw all afternoon no problem. Runs like it did 12
... Read more yrs ago. Pumps oil the would make Jed Clampet proud
My neighbor brought the saw to me. It was locked up
4 of 4 peoplefound this instruction helpful.
Marvin from KIRBYVILLE, TX
Really Easy
15 - 30 mins
Pliers, Screw drivers, Wrench (Adjustable)
He didn't want to spend alot of money on it. So I got the jug (Head) off and sanded it and the piston down while I waited on the new piston ring to get here. I found that it was easier putting the new ring in and the piston back into the jug (Head) was to go ahead and take the piston out so you could turn the jug (Head) upside down and it
... Read more slid right in. It didn't take no time at all. And it now runs as good as new