This Genuine OEM fuel filter is designed to maintain the performance and longevity of your equipment by preventing dirt and debris from entering the carburetor. Located inside the fuel tank, this essential component ensures clean fuel delivery, protecting the engine from potential damage caused by contaminants. Sold individually, the filt...Read moreer is built to meet original equipment standards for fit and function. Over time, the filter may become clogged, restricting fuel flow and making engine starts more difficult. For optimal performance, it should be replaced—not cleaned—at the first sign of blockage or wear.
This is a genuine OEM replacement part, it is sold individually. By pressing on the Purge Bulb, it will force fuel into the fuel line from the fuel tank into the carburetor. Once the carburetor is full of fuel, the excess fuel will be purged back into the tank in the fuel return line. Over time the primer will lose its elasticity or crack and need to be replaced. We have an article and video on
This Fuel Line is a 25-inch, clear, plastic line used to deliver fuel. It requires a screwdriver, pliers, socket set, and nut driver and is rated as "Easy" to install by customers. If the fuel line wear out to the point of breaking, cracks and/or leaking will appear and the part should be replaced. Refer to your make, model and diagram to ensure this is the correct part for you.
The Fuel Line Fitting is a plastic part which attaches two pieces of fuel line together. If broken due to damage/fatigue, there may be a leak and the part must be replaced. Installation is rated as "Easy". Refer to your make, model and diagram to ensure this part is correct for you.
This is an OEM replacement recoil kit supplied directly by Poulan. The starter pulley spins the flywheel to start the engine when you pull the starter rope. The most common reason for replacing the starter pulley is if the starter rope won't retract. Please note this kit does NOT include the rope and rewind spring. When replacing this part make sure to disconnect the spark plug wire before starting repair.
This part is the replacement fuel cap assembly for your chainsaw. It is made of black plastic and is sold individually. The fuel cap prevents fuel from spilling out of the chainsaw and prevents debris from entering the fuel tank. If the fuel cap is stripped or missing the O-ring, it can cause a leak, and will need to be replaced. To repla...Read morece the fuel cap simply screw the old one out and screw the new one in, ensuring you have a tight seal. This is an authentic OEM part sourced directly from the manufacturer.
Also referred to as a Recoil Spring, this OEM replacement part is used to rewind the pull rope back into the starter housing. This Spring is sold individually, not as part of a kit or assembly, and is made of metal.
If the pull cord will not retract into the housing, inspect the Recoil Spring for signs of wear or damage, replacing if ne...Read morecessary. You will need a screwdriver to complete this repair.
Customers rate this repair as Easy.
Dive into an efficient and effortless DIY repair work with this Poulan Carburetor Air Valve Assembly. Designed meticulously for chainsaws it plays an integral role in controlling the precise airflow from the air filter housing into the carburetor. To ensure maximum safety make sure to cool the engine and drain the gas tank before installi...Read moreng this durable assembly. It's always recommended to engage with such tasks in well-ventilated areas and don't forget to put on work gloves to safeguard your hands. Forge ahead with Poulan's innovative and trustworthy appliance parts for an unmatched working experience.
Genuine Manufacturer Approved replacement part used on specific Poulan Gas Chainsaws. This item is made out of Metal and it is Sold Individually. This part plays an important role as it provides spring action in the Pull Starter.
This is an OEM sourced replacement part used on Poulan chainsaws. A centrifugal clutch uses centrifugal force to connect two concentric shafts, with the driving shaft nested inside the driven shaft. Often centrifugal clutches will function even when they shouldn't, far beyond the point of when they need to be replaced. Keeping an eye on e...Read morequipment performance will determine when the clutch requires attention. This assembly includes metal clutch drum and a sprocket. To replace this item you would need a wrench set. • Remove the chain brake, bar, and chain. • Remove the cover and spark plug. • Bind the piston. (If you skip this step, the clutch will spin freely and you won't be able to remove it. If you have a piston stopper, just thread it into the spark plug hole. ) • Remove the clutch. • Replace old drum with a new assembly • Seat the clutch. • Unbind the piston. • Secure the bar, chain, and chain brake. • Tension the chain
The OEM Mounting Bar Nut is a nut used to install a mounting bar to your machine. Installation requires a wrench set and socket set, and is rated as "Easy". This nut attaches to the chainbar studs.
Husqvarna Genuine OEM Filter which is sold individually. The function of this part is to clean the air entering the carburetor on chainsaws. If the chainsaw engine stops after a few seconds or runs poorly it is recommended to replace the filter. Pleated Filters have proven to be efficient, effective, and cost-effective way to clean the air supplied into carburetor.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Albert - For model number 358350980
May 25, 2023
Is there only one chainsaw guide?
Hello Albert, thank you for the question. According to our research, your model comes with only one manual. We have attached the link to the manual. We hope this helps!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Pull cord failed to retract
5 of 6 peoplefound this instruction helpful.
Joel from West Roxbury, MA
Really Easy
Less than 15 mins
Removed cowling and spool. Spring drops in place without need for adjustment.
Was this helpful?
Thank you for voting!
Rope pulled out and didn't retrieve
4 of 6 peoplefound this instruction helpful.
Mike from Noble, OK
Really Easy
Less than 15 mins
Nutdriver
Pulled rope pull assembly housing, 4 screws and removed center screw that holds the eps plastic gear and spring was under neath that and it was bent out of shape. Important part is install new spring with yellow painted end outward , toward housing! Lucky I bought two??
Was this helpful?
Thank you for voting!
The saw started running too fast on idle and was over revving under light load.
3 of 3 peoplefound this instruction helpful.
Kenneth from Fremont, NE
Really Easy
30 - 60 mins
I tried a few adjustment on the carb jets and the idle speed but it got worse. I opened it up and discovered that the carburetor was loose and the engine was sucking air at the carburetor mount. One of the nuts was lost so I ordered a replacement part and a spare in case it happens again. This saw has worn out at least 6 chains, three gui
... Read morede bars and a sprocket. Had one other repair a year ago when it broke a clutch spring in the sprocket.