This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stopping in the middle of a cycle, you may need to replace the water inlet valve. Be sure to disconnect the power and water supply before you begin this repair.
This is a replacement sensor assembly for your washer. It may also be known as a motor rotor position sensor. The sensor assembly monitors the direction and speed of the spinning rotor and communicates this information to the electronic control board. If your washer pumps but will not spin or agitate, you may have a damaged sensor assembl...Read morey. This part is sold individually, and is an OEM part sourced directly from the manufacturer. Be sure to shut off the power to your washer before you begin this repair.
Clothing moves over a covered mounting point with help from this washer pulsator cap. The round plastic cover snaps into the center of the washplate, concealing the mounting bolt and providing a smooth surface above it. Cracks, broken retaining tabs, or a missing cap may expose the hardware or allow the cover to come loose during washing....Read more Replacing a damaged cap restores the finished washplate surface and helps keep garments from catching around the recessed bolt opening as laundry moves through the wash cycle. This is an OEM part sourced directly from the manufacturer.
This is a pulsator assembly, also known as an agitator, for your washing machine. This pulsator sits at the bottom of your washer and is what is used as the main driving force to wash your clothes. If the pulsator in your washer is broken, it will need replacing immediately to continue to wash and clean your clothes evenly. The cap that sits in the center of this part is sold separately.
Drain used wash water with this top-load washer drain pump assembly. Its motor drives an internal impeller that pushes water from the tub through the drain hose during drain and spin cycles. A worn motor, damaged impeller, or leaking housing may cause standing water, slow draining, loud buzzing, or puddles beneath the machine. Replacing a...Read more faulty pump helps restore proper drainage so wash cycles can finish normally. Unplug the washer, shut off the water supply, and prepare for leftover water before disconnecting hoses or wiring. This is an OEM part sourced directly from the manufacturer.
This washer tub-to-pump drain hose carries used water from the outer tub to the drain pump during draining. Its flexible, corrugated design accommodates tub movement while keeping water contained within the drainage path. Cracks, splits, or worn sections may cause leaks beneath the washer, while a collapsed section can restrict flow and l...Read moreeave water in the tub. Replacing a damaged hose helps restore proper drainage and a secure connection between the tub and pump, allowing wastewater to move out during wash and rinse cycles. This is an OEM part sourced directly from the manufacturer.
This drain hose is a genuine OEM replacement part supplied by LG for use in their washing machines. It is a light gray pipe with a diameter of 1.25 inches. The drain hose is connected to the drain pump, and it is responsible for transporting water out of the washing machine after a cycle. If the drain hose is kinked, damaged, or clogged, ...Read morethe washer will leak, or you may find standing water in the drum at the end of the cycle. Each drain hose comes with a metal clamp for fastening.
Secure attachment of washer components depends on fasteners that hold firmly during operation. This replacement washer screw restores an attachment where the original screw is missing, stripped, or damaged. Worn threads or a damaged head may prevent proper tightening and leave the attached component loose. Replacing faulty hardware helps ...Read morerestore a firm connection when the receiving threads and surrounding material remain intact. The screw can also be replaced during reassembly if damage prevents the original fastener from being tightened or removed normally. This is an OEM part sourced directly from the manufacturer.
Accurate water level sensing helps the washer fill and advance through its cycles correctly. This pressure sensor assembly measures changes in air pressure through a connected tube as water enters or leaves the tub. It sends water level information to the electronic control so filling can stop at the required level. A faulty sensor may ca...Read moreuse overfilling, underfilling, or interrupted wash cycles. Replacing a failed assembly helps restore reliable level feedback and controlled filling throughout the wash and rinse stages. This is an OEM part sourced directly from the manufacturer.
This part is the replacement fabric softener cap for your washer. It is also known as the washer dispenser drawer insert. It is made of blue plastic and is approximately 4 1/4 inches by 2 1/4 inches. The fabric softener fits inside the dispenser drawer and holds fabric softener and bleach. The main reason to replace this cap is if it is d...Read moreamaged or missing. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.
Keep the washer lid secure during operation with this lid switch and lock assembly. It detects whether the lid is closed and sends that information to the main control board. The locking mechanism holds the lid shut during high-speed spinning to help prevent accidental opening. A failed assembly may keep the washer from starting, leave th...Read moree lid unable to lock, or trigger a lock warning. Replacing a faulty unit helps restore proper lid detection and locking. Unplug the washer before accessing the assembly or disconnecting its wiring. This is an OEM part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
LE Error Message and won't spin drum properly
255 of 339 peoplefound this instruction helpful.
Mark from Harrisburg, PA
Easy
30 - 60 mins
Screw drivers, Socket set
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the
... Read more motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
Read less
Was this helpful?
Thank you for voting!
LE fail code
30 of 32 peoplefound this instruction helpful.
scott from GODDARD, KS
Really Easy
30 - 60 mins
Screw drivers, Socket set
Removed back of washer with screw driver, Removed outer motor cover with a 17 mm socket (1 bolt), Removed motor stater using 10 mm socket (8 bolts). Left motor plugged in and and tipped to the side exposing the sensor. Unplug and snap off sensor. Reassembled in opposite order. Machine works great. Very easy fix, and perfect fit on part.
Was this helpful?
Thank you for voting!
It did not drain water, cycle stops at rinse+spin.
28 of 36 peoplefound this instruction helpful.
Jesus from El Paso, TX
Very Easy
15 - 30 mins
Socket set, Wrench set
1-Take water off manually. 2- Take machine to back yard. 3- lay machine 45 degrees. 4- Located water bump, (rear left side). 5-removed drain black hoses with hand. 6-removed 3 screws from bump frame. 7-Taker off all unit and marked down cable position at plug. 8- installed new pump. 9- Reverse all steps. Note: I did not use new cable su
... Read morepplied with the new bump, I did not want to mess around on mother board connections, I kept old wire harness which are only two cables blue and gray. It took me less than 30 minutes.