Clothing moves over a covered mounting point with help from this washer pulsator cap. The round plastic cover snaps into the center of the washplate, concealing the mounting bolt and providing a smooth surface above it. Cracks, broken retaining tabs, or a missing cap may expose the hardware or allow the cover to come loose during washing....Read more Replacing a damaged cap restores the finished washplate surface and helps keep garments from catching around the recessed bolt opening as laundry moves through the wash cycle. This is an OEM part sourced directly from the manufacturer.
Drain used wash water with this top-load washer drain pump assembly. Its motor drives an internal impeller that pushes water from the tub through the drain hose during drain and spin cycles. A worn motor, damaged impeller, or leaking housing may cause standing water, slow draining, loud buzzing, or puddles beneath the machine. Replacing a...Read more faulty pump helps restore proper drainage so wash cycles can finish normally. Unplug the washer, shut off the water supply, and prepare for leftover water before disconnecting hoses or wiring. This is an OEM part sourced directly from the manufacturer.
This washer tub-to-pump drain hose carries used water from the outer tub to the drain pump during draining. Its flexible, corrugated design accommodates tub movement while keeping water contained within the drainage path. Cracks, splits, or worn sections may cause leaks beneath the washer, while a collapsed section can restrict flow and l...Read moreeave water in the tub. Replacing a damaged hose helps restore proper drainage and a secure connection between the tub and pump, allowing wastewater to move out during wash and rinse cycles. This is an OEM part sourced directly from the manufacturer.
This clutch housing assembly with mode shifter, or washer drive shaft and shifter assembly, is made for your washer. It connects the appliance wash plate to the motor so the washer can shift the drive system between the appliance spin and agitate cycles. Is measures 14.5 inches in diameter. You may need to replace this part if you hear strange noises or if the washer will not spin or agitate.
This drain hose is a genuine OEM replacement part supplied by LG for use in their washing machines. It is a light gray pipe with a diameter of 1.25 inches. The drain hose is connected to the drain pump, and it is responsible for transporting water out of the washing machine after a cycle. If the drain hose is kinked, damaged, or clogged, ...Read morethe washer will leak, or you may find standing water in the drum at the end of the cycle. Each drain hose comes with a metal clamp for fastening.
Secure attachment of washer components depends on fasteners that hold firmly during operation. This replacement washer screw restores an attachment where the original screw is missing, stripped, or damaged. Worn threads or a damaged head may prevent proper tightening and leave the attached component loose. Replacing faulty hardware helps ...Read morerestore a firm connection when the receiving threads and surrounding material remain intact. The screw can also be replaced during reassembly if damage prevents the original fastener from being tightened or removed normally. This is an OEM part sourced directly from the manufacturer.
A secure hose connection helps keep water contained inside the appliance. This hose clamp applies pressure around the hose end, holding it firmly against its fitting during operation. A weakened, bent, or broken clamp may allow the connection to loosen and leak into the cabinet or onto the floor. Replacing a damaged clamp helps restore th...Read moree grip needed to keep the hose attached and sealed. It secures the connection while allowing the hose to be removed when maintenance or replacement is required. This is an OEM part sourced directly from the manufacturer.
Rotational movement passes through this washer agitator coupling as the drive system operates during washing and spinning. The coupling engages adjoining drive components to transfer motion needed for normal laundry movement. Worn teeth, cracks, or a stripped connection may prevent agitation or spinning and cause unusual mechanical noises...Read more during operation. Replacing a damaged coupling helps restore engagement within the drive mechanism and reliable movement through the wash cycle. Its shaped surfaces provide the mechanical connection that allows the connected parts to move together under load. This is an OEM part sourced directly from the manufacturer.
This washer motor stator assembly creates the magnetic force that works with the rotor to turn the drum during washing and spinning. Its stationary wire coils receive electrical power to drive the motor without a belt. Damaged windings or broken connections may stop drum movement, cause jerking, or trigger a motor fault message. Replacing...Read more a failed stator helps restore controlled rotation, allowing laundry to move through the wash and water to be removed during spinning. The assembly forms the fixed section of the direct-drive motor. This is an OEM part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
It did not drain water, cycle stops at rinse+spin.
28 of 36 peoplefound this instruction helpful.
Jesus from El Paso, TX
Very Easy
15 - 30 mins
Socket set, Wrench set
1-Take water off manually. 2- Take machine to back yard. 3- lay machine 45 degrees. 4- Located water bump, (rear left side). 5-removed drain black hoses with hand. 6-removed 3 screws from bump frame. 7-Taker off all unit and marked down cable position at plug. 8- installed new pump. 9- Reverse all steps. Note: I did not use new cable su
... Read morepplied with the new bump, I did not want to mess around on mother board connections, I kept old wire harness which are only two cables blue and gray. It took me less than 30 minutes.
Read less
Was this helpful?
Thank you for voting!
LOUD GRINDING/ROARING NOISE, INTERMITTANT SPIN
10 of 13 peoplefound this instruction helpful.
MIKE from LANDENBERG, PA
A Bit Difficult
More than 2 hours
Pliers, Screw drivers, Socket set
Watch this video on youtube:https://www.youtube.com/watch?v=8ZKgP6hu8Fk very similar
Keep all parts separate and in order in a plastic box with dividers 1. Disconnect washer from wall. (electrical and hot/cold hoses, drain tube) 2. Remove center cap from bottom tub plate 3. Remove small bolt under cap 4. R
... Read moreemove bottom Tub Plate 5. Remover washer 6. Remove larger 38mm nut (I bought the correct deep well socket) Ive seen other video use a pipe wrench) 6a. Remove the large washer under nut NOTE- I did not remove the tub, total hassle, found it unnecessary, Yes the washer was heavier but nothing that cant be managed. 7. Place a blanket on the floor and lay the washer on its back to access the bottom. NOTE Everthing is nuts and bolts at this point. 10mm socket worked on all 8. Remove Nut & washer on rotor. Remove rotor-its has a line of magnets and the edges are sharp. Just wiggle it a bit. wear gloves if need be. 9. Remove bolts from Stator, user a small flat blade screw driver to undo 1 or 2 (some) electrical connections. Lay the stator aside. Move the electric connector(s) out of the way. 10. Remove the grounding wire at 6 oclock position 11.Remove the rectangular pack and the 3 oclock position by removing 2 bolts. It has a small arm that reaches out to the clutch arm, slide the piece out to the widest part of hole in clutch arrn an wiggle it loose. Almost there.... 12. Remove all the 10MM headed bolts from the clutsh and drive assemble The inner bolts are a slightly different style, keep the two sets separate. 13. Remove the clutch and drive.
NOTE: if the drive doesnt come out with a slight pull, you have missed a bolt(s)-inspect and remove as need be
14 Wipe clean the pocket in the outer wash tub that accepts the seal on the top of the drive. Lubricate the new drives seal completely with a little dishwasher detergent so it slides smoothly and seals well.
15. Assembly is the reverse:
Last Notes: *Install all bolts for the clutch and drive hand tight as you get everything lined up. *Once all bolt are in the clutch and drive are hand tight, tighten the bolts in a cross pattern as you would a wheels lug nuts *Snug the bolts used to attached the clutch and drive firmly 1/8 to 1/4 turn past snug *Make sure you clock the stator to the correct position, again hand tighten bolts then final tighten in a cross pattern. *The nut and washer in the rotor tighten to 1/4 to 1/2 turn past snug, its tight. *The large 38 MM nut on the top of the drive assembly torque is 88 ft lbs. Have a partner or friend hold the tub while you torque the large nut. If you don't have a torque wrench you can rent one from a number of auto-part chain stores. *I used a 1/2 Impact gun to remove the 38mm nut, Never use that kind of power to reassemble as it will damage parts.
Good luck, you can do it.
Read less
Was this helpful?
Thank you for voting!
Direct drive shaft broke right under the agitator plate.
6 of 7 peoplefound this instruction helpful.
EDWIN from FELTON, DE
Really Easy
30 - 60 mins
Nutdriver, Screw drivers, Socket set
Removed the inner tub laid the washer on its side with a blanket under it and Removed the assembly then the shaft assembly. Installed the new assembly and re assembled the rest of the washer (top and bottom) and plugged it in. Works great. TIP: you will need a big socket set for the tub retaining nut.