EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

34A - Overview

Models starting with 34A

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
GRATE BURNER – Part Number: W11400301
No Longer Available
GRATE BURNER
★★★★★
★★★★★
(2)
Part #W11400301
This square burner grate has sides measuring approximately nine inches. It is all black in color.
Nut-flglk 5/16-18 – Part Number: 712-04063
$6.40
In Stock
Nut-flglk 5/16-18
Part #712-04063
This nut is a manufacturer-approved replacement part for various lawn and garden equipment. It is sold individually, not as part of a kit or assembly. Also referred to as a Lock Nut, it is resistant to loosening when threaded on a bolt. It has a variety of applications and is used in multiple locations on most models. Please refer to your owners manual to determine the exact location. While made of durable metal, the ends can round off from improper use of a wrench or socket. Depending on the location, this part may also become worn through regular use of your machine. It should be replaced when visibly cracked, worn or damaged. To complete this repair, you will need a wrench or socket, and a torque wrench. Ensure you torque the bolt according to the manufacturer recommendations. Customers rate this repair as Easy.
Bell Blade Support – Part Number: 736-0524B-1
$6.40
In Stock
Bell Blade Support
Part #736-0524B-1
The Blade Support (Bell Blade Support) fits between the bottom of the blade and the blade bolt to provide support for the blade. It is installed underneath the cutting deck on the blade. Installation requires a hammer, 5/8 socket and torque wrench, and is rated as "Easy" by our customers. If broken or damaged (likely due to fatigue) you may hear a rattling sound coming from it, and the part should be replaced. This part is dark gray/silver, individually sold, and measures approx 3.5 x 1.25 inches. Refer to your make, model and diagrams to check if this is the correct part for you.
Burner Spark Ignition Switch – Part Number: WP7403P190-60
$65.73
In Stock
Burner Spark Ignition Switch
Part #WP7403P190-60
Sold individually.
Oven Door Gasket – Part Number: 7201P036-60
No Longer Available
Oven Door Stop – Part Number: 3420A033-34
No Longer Available
Oven Door Stop
Part #3420A033-34
DISCONTINUED – Part Number: 12001079
No Longer Available
DISCONTINUED
Part #12001079
Knob Kit - Black – Part Number: 12500102
No Longer Available
Knob Kit - Black
Part #12500102
This kit includes 4 burner knobs and 1 thermostat knob.
DISCONTINUED – Part Number: 7432P009-60
No Longer Available
DISCONTINUED
Part #7432P009-60
Use 914-0470 – Part Number: 714-0470
$6.40
In Stock
Use 914-0470
Part #714-0470
Pin-chute hinge – Part Number: 747-06290B
$6.55
On Order
Pin-chute hinge
Part #747-06290B
KIT-ARM REST – Part Number: 757-06093
$224.08
In Stock
KIT-ARM REST
Part #757-06093

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Igniter Switch on the burner was constantly on
8 of 15 people found this instruction helpful.
  • Roman from West Caldwell, NJ
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
To get to the switch I had to remove the knobs and the front panel of the burner valves. There were some dozen screws, top and bottom holding the panel in-place.
The switch slid off the burner valve stem easily but removing the wires I had to pull with the pliers. There seamed not to be a wire release that I could see.
Replacin g the wires was no problem. They slid into place by just pushing them in. Assembly was the reverse.
Was this helpful?
Thank you for voting!
Burned up oven door gasket needed replaced.
7 of 15 people found this instruction helpful.
  • Daniel from Prescott, MI
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Wrench (Adjustable)
I started by removing the door, then trying to remove all of the screws in the oven casing. Of course the very middle screw in the bottom of the oven was rusted and dammged by use. I had to use a drill bit and remove the old screw. After dissasembly of the oven casing, I found that the lip that supports the gasket was rusted and burnt awa y about 3/4 in. I placed the new gasket in and found that when closed it covered this defect and sealed. I reassembled and cheked for operation.Ok! Imortant--remove the elements before removing oven casing.
Was this helpful?
Thank you for voting!
Continuous sparking on all burners due to broken ignition switch
2 of 2 people found this instruction helpful.
  • Hannah from AMHERST, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
1. I accessed the burner ignition switches by lifting off stove top, sliding off burner knobs and oven knob, and removing the front switch cover (secured with 4 screws on top and 2 screws underneath).

2. I diagnosed which switch was broken: all four switches are wired together, so one faulty switch will affect sparking on both the left and right sides of the stove. I suspected a particular switch because that burner had occasionally struggled to ignite in recent weeks and felt "loose" when turned on.

After unplugging the stove from the electrical outlet and turning on the range fan, I slid several of the switches off their gas valve stems. When comparing the suspect switch to two other switches, the suspect switch felt "loose" when rotated and didn't have the same places of resistance that the other two had.

Feeling more confident that I had found the broken switch, I used pliers to pull out the four wires connecting the suspect switch to the other switches -- it took a good bit of force, there's no convenient release. Now I could access the switch terminals, so I used a multimeter to confirm that the suspect switch didn't have any change in electrical resistance when turned on/off -- it was broken.

3. I removed the broken switch and wired its neighbors together. I plugged the stove back in and checked that this had solved the problem -- no more continuous sparking, and the other three burners still worked.

While I waited several days for the replacement switch to arrive, I reassembled everything besides the broken burner's knob (to remind me to not use that burner), and continued using the other three burners normally.

4. When the replacement switch arrived, I inserted the original four wires into the new switch's terminal holes in the original configuration (again, it took a little force), reassembled everything, and was good to go.
Was this helpful?
Thank you for voting!