This fuel tank bushing grommet creates a tight seal where the fuel line enters the tank, helping prevent leaks and keep air and debris out of the fuel system. Made from durable, fuel-resistant rubber, it supports reliable engine performance and consistent fuel flow. Replacing a worn or damaged grommet can help eliminate leaks and restore proper operation.
This 25mm blade nut is a fastener that secures the blade to the spindle or shaft of your lawn equipment. It is located at the center of the blade. Signs of a broken blade nut include looseness, stripping, cracks, or excessive wear. Failing to replace a broken blade nut can result in a loose or dislodged blade during operation. To unthread...Read more the blade nut on your machine, use a wrench or socket to loosen it. This OEM component is sold individually. To ensure you have the correct number of blade nuts for your machine, refer to the user guide as your equipment may require multiple blade nuts. Consider replacing all of the nuts in one go as they wear out at similar rates.
It is an authentic OEM sourced hardware that is commonly utilized on Husqvarna handheld trimmers and blowers. This screw has multiple applications depending on unit, to ensure correct use of this hardware please make sure to check appropriate diagrams. Please note this hex socket head screw is sold individually.
Primarily used in chainsaws, this Starter Rope is an exact replacement part for hundreds of models. It is white and sold individually, not as part of a kit or assembly.
The Starter Rope will need to be replaced once you notice signs of it fraying, wearing, or it breaks off.
Customers rate this repair as Easy.
This stop button is a safety feature used in various types of lawn and garden equipment. It is a genuine OEM replacement part which is responsible for quickly shutting off the engine in case of an emergency or when it is no longer in use. The stop button is fitted into the handle controls for easy access. If the stop button becomes damage...Read mored or dislodged from its position, you will not be able to stop the equipment in an emergency. Therefore, it is important to replace the faulty stop button promptly to ensure that this emergency measure remains available, and avoid injury to the operator. Before beginning the repair, ensure that the equipment is turned off. Disconnect the stop button wires and detach the old stop button from the handle controls. Plug the new stop button in in place and reconnect the wires. If your equipment has fasteners with hex sockets, you will need to use a hex key/Allen wrench to remove and install the stop button. Ensure that the button is fitted securely before attempting to use your equipment again.
This is a genuine OEM approved replacement screw made for Husqvarna chainsaws and brush cutters. It is a standard hardware which has multiple uses based on your equipment. Please refer to diagrams for correct application. It is made out of metal and it is sold individually. You would need a torx screwdriver to install or remove this screw.
This is a genuine Husqvarna and Jonsered replacement part that has been sourced from the original manufacturer to be used with chainsaws, brushcutters, stump grinders, pruning saws, and power cutters. The sealing ring is used to provide spacing and to prevent oil leaks between the drive shaft and the cover panel. This item is sold as an individual replacement part.
This OEM locking pin is found in your handheld lawn equipment to hold a part, such as a cutting head, spool, or guard, in place and keep it from coming in loose while you are using your machine. If the pin is broken, the component it is supposed to be securing will become wobbly and loose, which can cause your machine to malfunction. To r...Read moreemove a broken locking pin, you can use pliers or a small screwdriver to pull it straight out of the hole. If the pin is stuck, you may need to wiggle it back and forth gently while pulling on it. Take into consideration that this part is sold individually, so refer to your instruction manual to confirm how many of these pins your machine will need.
The handle attaches to the clamping sleeve and is made of plastic. This is a genuine Husqvarna and Jonsered replacement part for use in trimmers, saws, and brushcutters. This item is available as an individual replacement part. During replacement, it may require a wrench to help install this part correctly. Over time this part may break and will need to be replaced.
This threaded plug bolt is a precision-designed component used to securely seal lubrication ports in gear housing assemblies on outdoor power equipment. Engineered with durable, corrosion-resistant material, it helps retain essential grease while preventing dirt, moisture, and debris from entering sensitive internal components. Its thread...Read moreed design ensures a tight, vibration-resistant fit, supporting long-lasting performance and proper gear protection. Ideal for maintenance or repair, it helps preserve smooth operation and extend the life of gear-driven systems.