This is the Genuine Craftsman replacement part. It is made out of Flexible Rubber and is Sold Individually. The purpose of the 530069216 Tank Purge Line is to return the excess fuel that is in the carburetor after the primer bulb has been pushed. The excess fuel is forced through the purge line back into the fuel tank. Over time the Tank Purge Line will become brittle and crack and will need to be replaced.
This is an authentic OEM replacement kit for use with lawn and garden equipment. Each kit includes the carburetor, cylinder, crankcase, and muffler gaskets. The carburetor gasket seals the area between the carburetor and engine block to prevent the entry of contaminants into the carburetor. The crankcase gasket prevents oil from leaking o...Read moreut of the crankcase. The cylinder and muffler gaskets prevent the combustion and exhaust gases from escaping. If you are experiencing common problems such as leaking, loss of compression, and poor engine performance this indicates that your gaskets may be worn down or damaged and need replacement. Carefully remove the old gaskets and thoroughly clean the mating surfaces where the new gaskets will be installed to ensure a good seal. Install the new gaskets and ensure that they fit properly.
This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with chainsaws. The oil cap connects to the saws chassis by covering the oil fill spout to prevent spills and to prevent contaminants from entering the oil tank. This item is available as an individual replacement part. Tools are not necessary to install this item.
This OEM bar adjustment retainer is a metal component that securely holds the adjustment screw and pin in place, allowing you to adjust the chain tension. It is typically located near the front of the chainsaw, close to the guide bar. If the guide bar is over-pressured, the retainer can become stressed and fail, causing it to ride up on t...Read morehe screw. Signs of a damaged retainer include visible breaks or deformations. You may also have trouble in tightening or loosening the chain, as the screw may become loose during adjustment. To remove a faulty retainer, remove the side cover by loosening the nuts and the tension screw on it with a socket. Unscrew the guide bar and replace the damaged retainer. When installing the new retainer, ensure the cone points towards the adjustment pin. Please note that the replacement retainer is sold separately from the guide bar and adjustment pin.
This is an authentic item sourced from original manufacturer. If the chainsaw bar doesn't adjust when you turn the tension screw usually the tension gear/pin or the adjustment bolt is worn or damaged. This part is made out of metal and it is sold individually. You would need a phillips head screwdriver to remove or secure this screw.
The Lock Nut is used to secure and lock parts in place. This is a gold, metal, individually sold part which can be installed with a wrench set, and socket set, and attaches onto various locations on a variety of equipment. If broken, damaged or worn, the part may be loose, and there may also be physical damage to the nut, at which time it...Read more should be replaced. Refer to your make, model and diagrams to ensure this is the correct part.
This is a genuine OEM sourced replacement part used with Poulan hedge trimmers. A spark plug delivers electric current from an ignition system to an internal combustion engine. After time spark plugs will become dirty or fouled. It is a good idea to replace the spark plug once this happens. This item is sold individually. You should gap y...Read moreour spark plug according to the owners manual of the outdoor product you have. You would need a spark plug wrench or a socket wrench to install this component.
This bar adjusting pin hooks onto the crankcase along with the bar adjust retainer and the screw. When you tighten the screw it helps to place tension on the bar. This high-quality pin is made out of metal and is sold individually. It is an authentic OEM sourced item which is specially produced for use with Poulan chainsaws. A screwdriver and a socket set may be needed when replacing this part.
This item is sold individually, but keep in mind that two may be needed. The lower isolator fits next to the retainer mount and helps to reduce vibrations. It is made of a hard rubber and will need to be replaced if it breaks. During the replacement process, a screwdriver may be required. This is a Poulan replacement part directly sourced from the manufacturer for gas chainsaws.
This authentic manufacturer-sourced component is specially designed for Poulan and Husqvarna gas-powered chainsaws. It is an identical replacement for a missing or a damaged retainer that is utilized to secure the piston pin. To ensure the exact location and the correct application of this product, refer to the appropriate diagrams for yo...Read moreur specific model. Keep in mind this high-quality hardware is made of durable metal and is sold as an individual item.