The OEM bearing, also known as the flange bearing, is silver, made of metal, and sold individually. It is used on riding mowers to secure the wheel in place and allow it to rotate freely on the shaft. Over time, the part may become worn and damaged, which you will notice if you experience a squealing or grinding sound from the wheel in qu...Read moreestion, or you notice the wheel is sloppy on the shaft.
You will need a hammer and punch to complete this repair, which most of our customers rated as easy. Make sure you tap the new bearing into place evenly inside the tire rim.
This genuine black cap axle, also sometimes known as the dust cap, is around 2 inches in diamater and sold individually. Comprised of plastic, it is designed to keep debris out of the hub and axle of your lawn mower or garden tractor. Over time, your dust cap may become damaged or lost due to wear and tear. If this happens, dirt and debri...Read mores can freely enter the axle and hub, causing damage.
This is an easy repair to make and does not require any tools. Just look for the cap axle on the rim of the wheel to make your repair.
Genuine Husqvarna replacement part, this part is sold individually. The 503939601 Air Purge does just what the part name says. It purges the air out of the carburetor. Then it forces fuel from the fuel tank and fuel line in to the carburetor.
This ready-oiled air filter is an OEM part that traps dirt and debris, preventing them from entering the engine. This part is black, comprised of foam, and is sold individually. Your air filter may become dirty and clogged over time, and because it is oiled, it is difficult to wash because it is oiled, so it will need to be replaced. A cl...Read moreogged air filter will cause your engine to run rough from restricted air flow.
This is an easy repair to make and does not require any special tools.
This OEM fuel line, or hose, is a 4-inch, clear, plastic tube which is sold individually. It is rated as "Easy" to install. This part connects to the purge assembly and delivers fuel to the carburetor or is used as a return line to the tank. A broken hose will leak, and should be replaced. Refer to your make, model and diagrams to check if this part is right for you.
The air cleaner knob, just over 1 inch in diameter, is black in color and made of plastic. It is sold individually, and its function is to tighten the air cleaner cover down on various lawn and garden equipment.
This knob can become worn over time, which will cause the air filter cover not to stay in place. Most of our customers find this to be an easy repair. It does not require any special tools.
This replacement screw is an authentic Husqvarna part. It is a genuine manufacturer approved part commonly used on a variety of power equipment including chainsaws, trimmers and sweepers. This standard hardware is utilized in many different placed depending on a tool. Please make sure to check appropriate diagrams to verify correct locati...Read moreon and application for this screw. It has hex head that will require a wrench to install or remove it and it is sold individually.
Used to seal the fuel tank to prevent leaks and allow the fuel line to enter through it, this Fuel Tank Bushing is sourced directly from the manufacturer. It is made of black rubber, is not part of a kit or assembly, and is sold individually.
This part will wear through regular use and should be replaced if you notice signs of damage or...Read more wear. When it malfunctions, you will see fuel leaking from the bushing. You will need a screwdriver and pliers to complete this repair.
Customers rate this repair as Easy.
This air filter comes in black foam and is rated as "Easy" to install. Installation requires a screwdriver, and the part attaches inside of the air cleaner housing. This manufacturer certified filter is used to prevent dirt and debris from entering the carburetor and engine, which would cause damage. If broken or clogged, the engine will ...Read moreexperience performane issues or may not turn on. If broken, the filter should be replaced. Tip: Put a bit of two-cycle oil in the bag and let it absorb into the filter. This makes it more tacky to catch debris.
The Starter Pawl bridge provides the resistance needed for the starter rope to start the trimming engine. It is an OEM part that attaches inside the recoil assembly. If broken due to weaar or fatigue, the engine will not engaged when the rope is pulled, and the part should be replaced. Installation is rated as easy and requires a screwdrv...Read moreier, pliers and nutdriver. Refer to your make, model and diagram to check if this part is correct. This part is metal, individually sold, and comes in gold.
This metal shoulder bolt, which is also called a shoulder screw or a stripper bolt, is a fastener that has a shoulder between the threaded and unthreaded sections of the bolt. This shoulder is a smooth section which supports and guides rotating parts. The threaded section of the bolt fastens parts of a machine together. This bolt has a di...Read moreameter of 5/6 inches, a thread pitch of 18 threads per inch, and a TT thread type. You can tell when a shoulder bolt is broken when the rotating parts that it is supporting becomes wobbly or misaligned. Your machine may even make unusual noises. You will need to replace a damaged shoulder bolt as soon as possible to prevent damage to your equipment. Left unrepaired, the rotating parts it is holding may become completely disconnected or collide with each other. To remove a shoulder bolt, you may need to use a wrench or socket to loosen the nut on the threaded end of it. Using a second wrench or pliers to hold the bolt in place while you loosen the nut can be helpful. Use the pliers to grip onto the shoulder of the bolt, then twist and pull the bolt out of your machine. Keep in mind that the nut does not come with this OEM-certified part, and that you need to purchase each bolt separately.
This OEM carburetor mixes the air-fuel mixture to the proper ratio for combustion in your engine. This carburetor is sold individually, is silver in color and metal in material, and is located on the intake of the engine.
Issues with your carburetor will cause problems with your engine running, and could cause excessive smoke due to too...Read more much gas. This can happen due to corrosion inside the carburetor. Carburetors can be rebuilt easily, and repairing them requires an allen wrench and a screwdriver. When troubleshooting your carb, remove the air filter and pour a teaspoon of fuel into the carburetor. Pull the starter rope, and if the engine starts then quickly dies, the carburetor is likely the problem.
When replacing your carburetor, also replace all gaskets when doing so, as they are a one-time use.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Would not start now runs great
6 of 6 peoplefound this instruction helpful.
JAMES from FAYETTEVILLE, AR
Very Easy
Less than 15 mins
Remove and replace
Was this helpful?
Thank you for voting!
Weed eater flooded constantly.
5 of 8 peoplefound this instruction helpful.
Richard from CHINA GROVE, NC
Very Easy
15 - 30 mins
Nutdriver
Very simple repair...took the old carburetor off and installed the new one. After replacement, the weed eater fired up after the second pull. Cover, removed 4 bolts. Carburetor, three bolts. Removed two hoses, choke handle and installed. Order gasket...never hurts to replace gaskets. One other thing, most important...use premix fuel!!! I
... Read moreuse it in all gas powered equipment now. Cleaner and does not gum up filters and carburetor.
Fixed up somebody's old trimmer they threw at the curb
5 of 11 peoplefound this instruction helpful.
Jeremy from DILLSBURG, PA
Easy
15 - 30 mins
This trimmer was in relatively good shape. Somebody had thrown it out! They thought they had broke the rewind, but when I ended up taking it off, it sucked right back in. They also must have broke the vibration plate on the bottom. With the screws and plate I bought from here, plus a new head and service kit I got elsewhere , this thing r
... Read morean like a champion again.