This OEM washer, also known as a flat washer, has dimensions of 25/32 x 1-1/4. Silver in color and metal, the washer is sold individually. Although this part can have a range of applications depending on the equipment, its general function is to spread the load under a bolt. Ensure you consult your owners manual or check your model number...Read more to confirm this is the washer you need for your equipment.
This part will need to be replaced when your existing one is worn or damaged. It is an easy repair according to our customers, and does not require any special tools.
Genuine Husqvarna replacement part, this part is sold individually. The 503939601 Air Purge does just what the part name says. It purges the air out of the carburetor. Then it forces fuel from the fuel tank and fuel line in to the carburetor.
This ready-oiled air filter is an OEM part that traps dirt and debris, preventing them from entering the engine. This part is black, comprised of foam, and is sold individually. Your air filter may become dirty and clogged over time, and because it is oiled, it is difficult to wash because it is oiled, so it will need to be replaced. A cl...Read moreogged air filter will cause your engine to run rough from restricted air flow.
This is an easy repair to make and does not require any special tools.
This OEM fuel line, or hose, is a 4-inch, clear, plastic tube which is sold individually. It is rated as "Easy" to install. This part connects to the purge assembly and delivers fuel to the carburetor or is used as a return line to the tank. A broken hose will leak, and should be replaced. Refer to your make, model and diagrams to check if this part is right for you.
This ignition switch is an OEM replacement part found near the steering wheel or dashboard in lawn tractors and riding mowers. The switch has four symbols on the top side which indicate its various functions including starting, stopping, running and reversing. The switch works by connecting/disconnecting the circuit between the battery an...Read mored the ignition system. The switch can fail either from physical damage or faulty electrical wiring. If the ignition switch is no longer working, you will not be able to operate your equipment. To access the faulty switch, first disconnect the battery, and wiring harness. Squeeze the tabs on the sides of the switch and pull it out from its mounting position. Plug the new switch in place and ensure that the tabs are engaged. Finish the repair by reconnecting the wiring harness and battery. If your current key is in good working condition, you can continue to use it. However, if it is not, it is recommended to replace the key at the same time. Each ignition switch is sold individually.
The air cleaner knob, just over 1 inch in diameter, is black in color and made of plastic. It is sold individually, and its function is to tighten the air cleaner cover down on various lawn and garden equipment.
This knob can become worn over time, which will cause the air filter cover not to stay in place. Most of our customers find this to be an easy repair. It does not require any special tools.
This replacement screw is an authentic Husqvarna part. It is a genuine manufacturer approved part commonly used on a variety of power equipment including chainsaws, trimmers and sweepers. This standard hardware is utilized in many different placed depending on a tool. Please make sure to check appropriate diagrams to verify correct locati...Read moreon and application for this screw. It has hex head that will require a wrench to install or remove it and it is sold individually.
Used to seal the fuel tank to prevent leaks and allow the fuel line to enter through it, this Fuel Tank Bushing is sourced directly from the manufacturer. It is made of black rubber, is not part of a kit or assembly, and is sold individually.
This part will wear through regular use and should be replaced if you notice signs of damage or...Read more wear. When it malfunctions, you will see fuel leaking from the bushing. You will need a screwdriver and pliers to complete this repair.
Customers rate this repair as Easy.
This is an OEM part guaranteed to fit Milwaukee power tools. This trigger spring is attached to main trigger. Please note that only trigger spring is included. When disassembling this area, be sure to slowly separate parts in order to prevent springs from being lost when released too quickly. Though they appear similar, a lockout spring i...Read mores a different part used with the throttle lockout (not present in all models). This part is often purchased with: • Trigger, part # 545066001 • Throttle Lockout, part # 530059804 • Lockout Spring, part # 545045601
This air filter comes in black foam and is rated as "Easy" to install. Installation requires a screwdriver, and the part attaches inside of the air cleaner housing. This manufacturer certified filter is used to prevent dirt and debris from entering the carburetor and engine, which would cause damage. If broken or clogged, the engine will ...Read moreexperience performane issues or may not turn on. If broken, the filter should be replaced. Tip: Put a bit of two-cycle oil in the bag and let it absorb into the filter. This makes it more tacky to catch debris.
This is a genuine OEM replacement part used with many lawn tractor engines. The Craftsman screw (1/4-20 x 5/8) secures the cover to the riding mower deck housing. This hardened metal item is sold individually. Keep in mind three are needed for the repair, and a wrench is required for making the replacement.
This replacement air cleaner cover is designed for use with Husqvarna gas powered lawn and garden equipment. This cover is used to secure the air filter in the housing. It is made out of durable plastic and it is sold individually. Please note, the knob and the bolt are both sold separately. Replacing this part does not require any tools.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Would not start now runs great
6 of 6 peoplefound this instruction helpful.
JAMES from FAYETTEVILLE, AR
Very Easy
Less than 15 mins
Remove and replace
Was this helpful?
Thank you for voting!
Weed eater flooded constantly.
5 of 8 peoplefound this instruction helpful.
Richard from CHINA GROVE, NC
Very Easy
15 - 30 mins
Nutdriver
Very simple repair...took the old carburetor off and installed the new one. After replacement, the weed eater fired up after the second pull. Cover, removed 4 bolts. Carburetor, three bolts. Removed two hoses, choke handle and installed. Order gasket...never hurts to replace gaskets. One other thing, most important...use premix fuel!!! I
... Read moreuse it in all gas powered equipment now. Cleaner and does not gum up filters and carburetor.
Fixed up somebody's old trimmer they threw at the curb
5 of 11 peoplefound this instruction helpful.
Jeremy from DILLSBURG, PA
Easy
15 - 30 mins
This trimmer was in relatively good shape. Somebody had thrown it out! They thought they had broke the rewind, but when I ended up taking it off, it sucked right back in. They also must have broke the vibration plate on the bottom. With the screws and plate I bought from here, plus a new head and service kit I got elsewhere , this thing r
... Read morean like a champion again.