This nut is a manufacturer-approved replacement part for various lawn and garden equipment. It is sold individually, not as part of a kit or assembly. Also referred to as a Lock Nut, it is resistant to loosening when threaded on a bolt. It has a variety of applications and is used in multiple locations on most models. Please refer to your...Read more owners manual to determine the exact location.
While made of durable metal, the ends can round off from improper use of a wrench or socket. Depending on the location, this part may also become worn through regular use of your machine. It should be replaced when visibly cracked, worn or damaged. To complete this repair, you will need a wrench or socket, and a torque wrench. Ensure you torque the bolt according to the manufacturer recommendations.
Customers rate this repair as Easy.
This part is sold by color. Please see color options below to see what part number you need to order. Color: Majestic Orange. Part Number: 790-00121-0606. Color: Powder Black. Part Number: 790-00121-0637. Color: MTD/Troy-Bilt Red. Part Number: 790-00121-0638. Color: Red Metallic. Part Number: 790-00121-0650. Color: Oyster Gray. Part ...Read moreNumber: 790-00121-0662. Color: Polo Green. Part Number: 790-00121-0689. Color: Black Jack. Part Number: 790-00121-0691. Color: Mastercraft Green. Part Number: 790-00121-0709. Color: Sears Red. Part Number: 790-00121-4044. Color: Cub Yellow-2. Part Number: 790-00121-4021. Color: Fint Mica. Part Number: 790-00121-4033. Color: Pure Orange. Part Number: 790-00121-4041.
This replacement shave plate is a high-quality item supplied directly from original equipment manufacturer for use with snow throwers. Its purpose is to scrape the ground to help pick up the snow. Shave plates are designed to absorb a lot of friction while the machine is in operation. You can tell that a snowblower has a worn shave plate ...Read morebecause it will no longer be able to clear the sidewalk, leaving patches behind. Please note, paddles and scrapers are designed to wear at approximately the same rate, so it's always a good idea to replace them both at the same time. This durable shave plate is sold individually.
This authentic manufacturer-supplied part is designed for Craftsman snowblowers. Flange bushings are used to provide support for components while allowing them to rotate with minimum friction. It is made of high-quality material and is sold individually. Make sure to check the diagrams for your model to ensure the correct replacement proc...Read moreedure. You may need a screwdriver and a wrench set to take apart and reassemble the equipment when performing this repair.
This is an authentic replacement part manufactured for use with Ryobi snowthrowers. The grease plug is commonly used to seal the oil port on the augers gearcase assembly. This grease plug is available as an individual replacement part, please see model diagram for associative parts.
This replacement part is an authentic manufacturer-sourced component which is specially designed for use with snowthrowers. It is mounted to the lower chute to help direct the snow away from the unit. This part is made of high-quality plastic material and it is sold individually, please note the hardware to secure it is sold separately.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Original shave plate badly worn
12 of 25 peoplefound this instruction helpful.
John from HARRISVILLE, NH
Really Easy
Less than 15 mins
Wrench set
With WD-40 or equivalent, spray the four nuts on the underside of the snow blower housing that hold the shave plate to the housing. Also spray the two bolts that hold the shave plate to the side of the housing. Let sit for a few minutes and using a 1/2" box end wrench remove the four nuts on the bottom of the housing. If necessary, app
... Read morely heat with a torch to loosen. Using a 9/16" box end wrench, remove the nuts on the sides (these also hold the adjustable skid feet). It is recommended that the bottom bolts and nuts be replaced with 5/16-18 X 3/4" long zinc plated carriage bolts using zinc plated washers and ny-lock nuts. It is also recommended that all of th screw threads be coated with an anti- seize lubricant so disassembly at a later date will be easy.