This carriage bolt measures 5/16-18 x .75 and fastens two parts in your machine together. It has a round domed head and a square underside so the bolt does not rotate once it has been secured into place. If it has signs of deformation or wear, you will need to replace it. To unthread this bolt, you need an adjustable wrench to loosen the ...Read morenut found on the end of the bolt. You may need to apply a lubricating oil to the bolt if it is stuck. You may need to clamp down on the head of the bolt with pliers while continuing to turn the nut counterclockwise. You can then slide the carriage bolt out of its hole or tap it gently with a hammer. This bolt is a standalone product and the nut is not included. This bolt was sourced directly from its manufacturer.
This is a shear bolt, also known as a snap-off bolt. This is a fastener designed to break under a specific amount of pressure and protect the machine it is installed on from that excessive load. In lawn equipment, the shear bolts typically connect the auger or blade to the drive shaft. Therefore, if the bolt snaps, the auger gets jammed a...Read morend cannot rotate so that it will not damage the rest of the unit. This bolt has a diameter of 5/16 inches, with 18 threads per inch, and is 1.5 inches long. To remove the shear bolt from your machine, you need to turn the power off first. With pliers or a wrench, grip onto the broken end of the bolt and twist it gently out of its hole. If it is stuck, you may need to coat the bolt with a penetrating oil or tap the bolt out with a mallet. Since this authentic OEM part is sold individually, refer to your instruction manual so that you can purchase the correct number of bolts for your machine.
This chute flange keeper is sourced from the original equipment manufacturer for use in snowblowers. The plastic keeper allows the snowblower chute to pivot, and secures the flange that connects the chute to the blower frame and holds it in place during use. Over time the flange keeper can break or fall off, which causes the chute to disl...Read moreodge or shift from its position. If you notice that debris is discharged in the wrong direction, and you have difficulties adjusting the chute then this is a sign that the flange keeper is no longer functioning as it should. Clean the chute flange and surrounding area before placing the new keeper on. Use a pair of pliers to align the the holes on the flange keeper with the holes on the chute and lock it in place.
This is an authentic OEM sourced replacement part designed for use with snow throwers/blowers. It allows you to engage and disengage the unit. This cable is sold individually. You may need pliers to complete this repair. • Remove the cable end from the control head and install the new one • Now you can run the new cable down to the ...Read morecontrol handle • Attach the other end of the cable • Tie the cable in place just as the old one was, but leave enough clearance and free play to avoid over-bending and breaking the new cable
This is an authentic OEM part for Craftsman lawn and garden equipment. This bushing has an internal diameter of 0.380", is made of durable black plastic, is not part of an assembly or kit, and is sold individually. The purpose of this bushing is to ensure there is a tight fit between parts.
A common sign this part needs to be replaced i...Read mores if you notice any parts loosely connected or detached. This part will become worn through regular use of the machine. It is located in various areas, depending on your model. Refer to your owner's manual for the exact location. You will need a wrench and pliers to complete this repair.
Customers rate this repair as Medium difficulty.
This item is a genuine OEM replacement part that is intended to be used with snowthrowers and lawnmowers from Ryobi, MTD, Yard Machines, Troy-Bilt, Bolens, and Yard-Man. The metal hex head screw is used with different types of machines and the application of the screw can vary based on the model of the equipment. This screw is sold as an individual replacement part.
Used mainly in snow blowers, this flange bearing is typically installed on the axle and creates a tight fit with little friction while still allowing for movement.?Your equipment will likely feature multiple of these bearings, so refer to any diagrams for your model to determine whether you will need one, or more. This is an OEM part that...Read more is sold as an individual item and has a 0.75-inch inner-diameter, 1-inch outer-diameter, and 1-inch height.
This item has been sourced from the original manufacturer to be used with snowblowers from MTD, Ryobi, Yard Machines, Bolens, and Yard-Man. This item is the hard rubber tire that fits onto the friction wheel and is used to rotate the friction disc. Overtime this item can wear down and need to be replaced to make good contact with the friction disc. This item is available as an individual replacement part.
Sourced directly from the original manufacturer, this Bell Washer is made of gold-colored metal and is sold individually, not as part of a kit or assembly. It is used to provide spacing between various part assemblies along a shaft.
If you hear a strange noise coming from the shaft area, or you notice the Washer is visibly worn or damag...Read moreed, it will need to be replaced. Refer to your owners manual to determine the exact location of this part.
Customers rate the difficulty of this repair as Medium.
This silver metal lock washer helps prevent the nut on the drive belt pulley shaft from backing off during operation, it has a 5/16-inch inner diameter and a 1/2-inch outer diameter. one washer is included, replace it if fatigue or damage allows the connected shafts to spin freely, verify fit using the equipment model or owner manual
This part is made of metal and is available individually. The shift lever spring attaches to the shift lever. A socket set may be helpful when replacing this item. It may become broken and will need to be replaced. This is an OEM MTD, Bolens, and Yard Machines part directly sourced from the manufacturer for use in snow blowers.
It is an authentic replacement part that is supplied by original equipment manufacturer, it is specially designed for use with snowblowers. This is the cover for the belt to protect it and the pulleys from dirt and debris. It is made from durable, high-quality plastic material and it is sold individually.